Skip to content
Aussieveedubbers

Push Rod Tubes

0 likes
Share Share on Facebook Share on X Share on Reddit
Log in to reply

VolksFolks Son of Jim - Creator of Good

2,869 posts · joined Dec 2003 ·

#133131
Today i was to reseal the exhaust on my 75 kombi, removed the exhaust, and removed the manifold from the motor, sealed i and replaced it, upon tightening the studs one rusty little feker sheared off, so i removed the exhaused again and tried to remove the stud from the head with some vice grips, fec me it broke again,so i welded some threaded rod as a temp measure which worked fine, when it broke i dented a push rod tube, all looked ok but after starting the motor and was quiet as a whistle, but wait oil pissing out everywhere, the dent to the tube must of been worse than i thought, are these rods easy to replace/seal, or does the head have to come off, not too worried about the head coming off as i can replace the stud, but any tips would be great!! thanks


Andy
They laugh because You are different, You laugh because They are all the same.

check out www.lowlight.com.au for low lights only..

Old Dubber Wolfsburg Wizard

605 posts · joined Aug 2002 ·

#133139
Andy,
No, you do not have to remove the head. Pop off the rocker cover, remove rocker gear, pushrod and spring wire retainer, then pushrod tube can be removed.
Grahame
visit my club site at www.vwdcqinc.org.au

Craig Torrens 6 times Australian, 7 times State Hillclimb Class Champion

8,040 posts · joined Jan 2003 ·

#133141
Head needs to come off to replace original pushrod tubes as they are a crush fit.
You can buy tubes that are two piece and adjustable. They're made from machined aluminum and work well ! These can be fitted without removing the head.
There is also a two piece with a spring, these are shit !

Or you could use the good old tube of silicon !


Bizarre Moderator The artist formerly known as blue74l

12,785 posts · joined Aug 2002 ·

#133142
Nah - fairly easy

I take it is a Type 4???

Take the rocker cover off

Closely look how the spring thing goes in at the bottom of the rocker. Only peel half off.

Take rocker off

If you have a pair of decent cir clip pliers that have the knurl on the out side push that in and "carefully" pull the tube out through the head. If you dont have the plier things a pair of long nose pliers and feed it through. ..... guess you dont need to be too careful - its already a stuffed tube.

There are O rings top and bottom. I would replace those

reverse and do tappets if not hydro

TTFN

Barry
Futue te ipsum!!!

Bizarre Moderator The artist formerly known as blue74l

12,785 posts · joined Aug 2002 ·

#133148
Ohhhh.... I HOPE its a Type 4.

75 Kombi

working on exhaust from the bottom

Craig got it wrong! :o

Craig got it wrong! :o

Craig got it wrong! :o

Craig got it wrong! :o

Craig got it wrong! :o

Craig got it wrong! :o

Craig got it wrong! :o

Craig got it wrong! :o

TTFN

BArry
Futue te ipsum!!!

Craig Torrens 6 times Australian, 7 times State Hillclimb Class Champion

8,040 posts · joined Jan 2003 ·

#133151
Craig Torrens wrote:Head needs to come off to replace original pushrod tubes as they are a crush fit.
You can buy tubes that are two piece and adjustable. They're made from machined aluminum and work well ! These can be fitted without removing the head.
There is also a two piece with a spring, these are shit !

Or you could use the good old tube of silicon !

0000ps forgot to read it was a Kombi !!!!!


I hope it is a Type 1 motor !!!


Bizarre Moderator The artist formerly known as blue74l

12,785 posts · joined Aug 2002 ·

#133152
C'mon Andy

What is it???????

I reckon there is a beer or 3 riding on this!!! :bounce


:beer:beer:beer


Yep - 3 beers! I can see em!
Futue te ipsum!!!

vw54 Administrator Always Waiting 4 Friday

16,723 posts · joined Aug 2002 ·

#133158
I recon its a 1600 engine only cause theres a BEER riding on this one... BARRY.. your SHOUT...


I bet its a 2litre.... as it should be in a 75 Kombi unless some one has done the old switch a rooooooooooo

:beer:beer:beer:beer
I read it on FACEBOOK so it must be true


http://forums.aussieveedubbers.com/viewtopic.php?tid=91278&page=1#pid848630


http://forums.aussieveedubbers.com/viewtopic.php?tid=63561&page=1#pid624099


http://forums.aussieveedubbers.com/viewtopic.php?tid=4832&page=1#pid452603


http://forums.aussieveedubbers.com/viewtopic.php?tid=60650&page=1#pid574409

VolksFolks Son of Jim - Creator of Good

2,869 posts · joined Dec 2003 ·

#133161
1800 or 2.0, not sure?
They laugh because You are different, You laugh because They are all the same.

check out www.lowlight.com.au for low lights only..

Craig Torrens 6 times Australian, 7 times State Hillclimb Class Champion

8,040 posts · joined Jan 2003 ·

#133166
So Barry, daves buying us a beer.:P


VolksFolks Son of Jim - Creator of Good

2,869 posts · joined Dec 2003 ·

#133172
They laugh because You are different, You laugh because They are all the same.

check out www.lowlight.com.au for low lights only..

vw54 Administrator Always Waiting 4 Friday

16,723 posts · joined Aug 2002 ·

#133173
No i was just havin a side bet

You can both come along to the next meeting on 19FEB n buy me a beer,

:beer:beer:beer:beer
I read it on FACEBOOK so it must be true


http://forums.aussieveedubbers.com/viewtopic.php?tid=91278&page=1#pid848630


http://forums.aussieveedubbers.com/viewtopic.php?tid=63561&page=1#pid624099


http://forums.aussieveedubbers.com/viewtopic.php?tid=4832&page=1#pid452603


http://forums.aussieveedubbers.com/viewtopic.php?tid=60650&page=1#pid574409

VolksFolks Son of Jim - Creator of Good

2,869 posts · joined Dec 2003 ·

#133176
where can i get a replacement tube from, vw dealer?


Andy
They laugh because You are different, You laugh because They are all the same.

check out www.lowlight.com.au for low lights only..

Craig Torrens 6 times Australian, 7 times State Hillclimb Class Champion

8,040 posts · joined Jan 2003 ·

#133203
vw54 wrote:No i was just havin a side bet

You can both come along to the next meeting on 19FEB n buy me a beer,

:beer:beer:beer:beer

Do we need to wear white sheets with holes for our eyes😀 do I need to bring a goat or a virgin ?


vw54 Administrator Always Waiting 4 Friday

16,723 posts · joined Aug 2002 ·

#133313
Ring Vintage Vee Dub in Sydney 02-9789-1777, they can ship the tubes n seals down to you.


Craig yes please bring along a Virgin... ( if you can find one )

What would we do with a goat ???
I read it on FACEBOOK so it must be true


http://forums.aussieveedubbers.com/viewtopic.php?tid=91278&page=1#pid848630


http://forums.aussieveedubbers.com/viewtopic.php?tid=63561&page=1#pid624099


http://forums.aussieveedubbers.com/viewtopic.php?tid=4832&page=1#pid452603


http://forums.aussieveedubbers.com/viewtopic.php?tid=60650&page=1#pid574409