Skip to content
Aussieveedubbers

What Causes this??????

0 likes
Share Share on Facebook Share on X Share on Reddit

pod i`ve got to finish this thing one day

4,980 posts · joined Dec 2003 ·

#155373
took out my 1200 the other day removed tinware to check on oil leaks found oil all around cylinder head join on oil cooler side but not coming from cooler, any ideas before I start spending money or is it worth going to a 1600 etc

1 attachment · Log in to view

meetings 1st sunday of the month
check wbsite for location
All Welcome
http://www.flatfour.org/
and on Facebook https://www.facebook.com/FlatFour

Craig Torrens 6 times Australian, 7 times State Hillclimb Class Champion

8,040 posts · joined Jan 2003 ·

#155387
loose head nuts or a pulled head stud.

Check the torque of your head nuts.


Che Castro ankle straps

1,945 posts · joined Aug 2002 ·

#155595
if it is a pulled head stud then you should get a clackety clackety noise when you drive (it is an exhaust leak). Also the engine will pop and crack randomnly and run pretty unevenly and weak. It's hard to gauge this if the car has always been like this.

When the oil cooler leaks it tends to run down the side of the case - i doubt it is a oil cooler leak

Going to a 1600 isnt a bad idea. remember 1200 parts are hard to get hold of, and if the case is shagged then you dont really have any other options.
Jon

pod i`ve got to finish this thing one day

4,980 posts · joined Dec 2003 ·

#155886
ì will investigate further over the easter break ,apart from going to nats on sunday. it did have exhaust leak in the j pipe that side but havent put new pipes on and had it started as pulled motor to do a little rust repair .
thanks paul
meetings 1st sunday of the month
check wbsite for location
All Welcome
http://www.flatfour.org/
and on Facebook https://www.facebook.com/FlatFour

68AutoBug Beetle Restorer - Experience over 138\% - YIKES --

11,654 posts · joined Aug 2002 ·

#155894
Oil from the oil cooler can be blown anywhere...
but it does look like the oil has been blown out of the cylinder
I would also go for the 1600 engine....
with the doghouse oil cooler wider cooling fan etc...
Best of luck..

Or You could add case savers to the 1200 engine....

Lee
- Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY---

pod i`ve got to finish this thing one day

4,980 posts · joined Dec 2003 ·

#155986
what would the ballpark figure be for 1600 motor would this be 6 volt as i would like to keep it as a 6 volt system etc. whats needed in the conversion as $ are harder to get out of the minister for war and finances
meetings 1st sunday of the month
check wbsite for location
All Welcome
http://www.flatfour.org/
and on Facebook https://www.facebook.com/FlatFour

Che Castro ankle straps

1,945 posts · joined Aug 2002 ·

#156027
to rebuild a 1600 u probably need about $1500 at least.
Jon

Peter Leonard Moderator Volatile

1,456 posts · joined Apr 2003 ·

#157644
looks fine to me...:alien how old is it?
crikeys! is it doing anything wrong besides looking a wee bit oily? unless it's fully pouring out, just keep puttin around i say. in my unexpert opinion... you find that you have 'semi-floating barrels'. no biggy. not blowing heaps of smoke is it?
let sleeping dubs lie

pod i`ve got to finish this thing one day

4,980 posts · joined Dec 2003 ·

#157651
a little bit from that side checking it out on weekend ,was thinking of doing rings and bearings before putting it back in, but if its no good another motor here i come:o
meetings 1st sunday of the month
check wbsite for location
All Welcome
http://www.flatfour.org/
and on Facebook https://www.facebook.com/FlatFour