Skip to content
Aussieveedubbers

putting sparkplugs back in

0 likes
Share Share on Facebook Share on X Share on Reddit

Purple Martin Fahrvergnugen

913 posts · joined Feb 2003 ·

#347709
Hi,

I took the sparkplugs out of my 2L kombi, and now I can't get two of them back in! The two nearest the rear bumper seem impossible because I can't reach through the small hole in the tinware by hand to get the thread started. Is there some special trick to getting them back in?

Thanks!
1959 red & white Beetle
1975 Kombi camper

Midlife crisis Nartispuddlejumper, Bureau of Toxicity

2,282 posts · joined May 2003 ·

#347714
I use a good brand spark plug socket make sure the rubber plug is inside it to hold plug in tight and be carefull not to cross thread.

hope this helps

Marc
If you can't laugh at yourself you can't laugh at anyone else! Because life is to short not to LAUGH

VolksFolks Son of Jim - Creator of Good

2,869 posts · joined Dec 2003 ·

#347717
haha, dont ya just love it ay!, i stripped down a motor and found 6 loose plugs under the tinware, obviously somone must of swore a little.

Andy

oh yeh as marc said..
They laugh because You are different, You laugh because They are all the same.

check out www.lowlight.com.au for low lights only..

BiX Veteran Volks Folk

2,499 posts · joined Sep 2002 ·

#347754
use a little bit of plastic pipe, or a good socket, with the above mentioned rubber ring.

bit of garden hose, if its soft.
I have no sympathy for my car, only the wallet that pays for it!
Go hard or go home!!!!

eraser Fahrvergnugen

970 posts · joined Mar 2005 ·

#348309
just dont push the socket on too tight as otherwise u will tighten the spark plug go to pull the ratchet and the socket out and the ratchet will come off the socket and u will spend a good 30 minutes trying to pull the bloody thing out(or just re-attatch the spark plug undo this time dont push it in so far 😉)
-M

Robo Compulsive Aussie Vee Dubber

4,491 posts · joined Feb 2003 ·

#348352
Yeah don't ya just hate that! My sidchrome socket has a very tight rubber bit in it, it dose get stuck sometime's I just use a pair of multigrips cause the have angled jaws and I gently pull the socket out.
Rob...
Boxer Power
Member of DMLRK.....Die Mittler Lebuns Resto Komeradschaft

Purple Martin Fahrvergnugen

913 posts · joined Feb 2003 ·

#348702
I've tried it with a spark-plug socket with a rubber holder, and I've tried it with some rubber hose... still no luck 🙁
1959 red & white Beetle
1975 Kombi camper

Robo Compulsive Aussie Vee Dubber

4,491 posts · joined Feb 2003 ·

#348857
Ya have to get the angle just right. get a small torch and have a look through the hole, you should be able to visual the thread and get an idea what angle they go in.
Rob...
Boxer Power
Member of DMLRK.....Die Mittler Lebuns Resto Komeradschaft

aggri1 Insano Dub Head

824 posts · joined Dec 2003 ·

#349234
Mmm, that slightly off angle (both directions isn't it?) takes a while to figure out hey!

I use the spark plug socket with the rubber insert just fine. And I too found old plugs under the tinware.

BiX Veteran Volks Folk

2,499 posts · joined Sep 2002 ·

#349255
i have holes in the side of the engine bay...... just use an extension and a spark plug spanner and in they go!!
I have no sympathy for my car, only the wallet that pays for it!
Go hard or go home!!!!

manxed69 Officially Full-On Dubber

211 posts · joined Aug 2002 ·

#349904
You need to feel your way.

I always put a drop of oil on the thread before they go in to lubricate the thread. It also helps you feel when the spark plug is seating against the head.

fetid_swamp Seriously Crusin Dubber

174 posts · joined Sep 2003 ·

#349925
all of the above except a quality magnetic spark plug socket. rubber rings suck... finger for the initial thread. use a 3/8 drive so you dont tighten too much when you apply the ratcheet.
works for me..

Purple Martin Fahrvergnugen

913 posts · joined Feb 2003 ·

#349986
Thanks guys I'll try those tricks.
1959 red & white Beetle
1975 Kombi camper

BiX Veteran Volks Folk

2,499 posts · joined Sep 2002 ·

#349987
don't put oil on, as it wil carbonize and make them harder to get out, get some proper anti seiaze. there is a copper one and other ones like that designed for high temps.
I have no sympathy for my car, only the wallet that pays for it!
Go hard or go home!!!!

toplessbug Fahrvergnugen

879 posts · joined Aug 2002 ·

#350304
yea what bix said never put oil on them use anti seize and t4 have a funny angle i found a plug socket and small extn works well just pull out the rubber ring and cut the center out till it just holds the plug and its easy to get off without leaving the socket or ring behind

Purple Martin Fahrvergnugen

913 posts · joined Feb 2003 ·

#351268
Well I got them in at last! Using a torch and a small mirror really helped see through the tinware to the hole in the head, and using a bit of rubber air hose on the end of the plugs I was able to position them and get the threads started, then finished them off with the spark-plug tool.

I did use a bit of oil, it was before I read the two posts above, but I'll be rebuilding this motor now so luckily the oil won't matter this time. I was only putting the plugs in to get the motor running so I could drive the Kombi from the front of the house round to the back where I'll drop the motor out. I moved it yesterday and jacked it up, today I'll make a start!
1959 red & white Beetle
1975 Kombi camper