I am after a 36 mm nut axle wacker or info on who sells them in Australia. There was a bloke selling them recently on ebay as well as engine cradles etc. Cant seem to find his adds at the moment.
Cheers Nicko
Hey i got a Yankie easy off, you can brake the nuts of with your little finger its that easy, these also fit the fly wheel gland nuts, $125 plus post, worth every cent!
Andynn[ Edited on 25-8-05 by VolksFolks ]
They laugh because You are different, You laugh because They are all the same.
check out
www.lowlight.com.au for low lights only..
A big socket is what I use... but it cost a few $
Pay your debts, CxxT
Big socket and 3/4 inch breaker bar. works everytime!!
I have no sympathy for my car, only the wallet that pays for it!
Go hard or go home!!!!
Nut whacker + sledge.. works everytime :P
Or nut whacker plus 3/4 BB.
I got mine for about $12 from Cip1
.
Yasdnil01....also advertises in Just Parts.....
Andy how much to post to 2340. I am thinking about it. Just snapped my breaker bar. Knew I should of hung 6 foot of water pipe on to get that extra leverage.
Nicko
Does anyone have Yasdnil01 email address?
Nicko
Nicko, $8 postage mate
Andy
They laugh because You are different, You laugh because They are all the same.
check out
www.lowlight.com.au for low lights only..
I have one of those tools that Andy is selling.
It is an absolute MUST for any serious kraut builder. I bought it from the states a long time ago.
tell me how you are going to get the gland nut off an engine flywheel when the engine is on the floor and your mates are not around.
Tell me how you get that pesky axle nut off the old gearbox you found in the bush or the car is blocked up offen the ground and you dun have a m8 around to jam the brake pedal to the floor (assuming the brakes work at all)?
Thats right, you cant unless you have mates around or a gas axe handy.
This little gem gets them off without having to stop the engine or the axle from turning and you can use a 3/8" drive ratchet to do it.
No swearing and cursing, bashing the shit out of breaker bars and great chunk of steam pipe, engines leaping about all over the floor and the entire diff rolling along the floor as you madly chase it along all the while bashing the shit out of it.
The first time you do an axle nut up to 270 ft/lb you think you have stripped it it is sooo easy.
Stick your big sockets and bloody breaker bars and lengths of water pie and the rest of the garbage needed to hold the engine/axle down right up you arses.😁😁
This tool has paid for itself time and time again!!!!
I will rent you mine for 50 bucks LMAO, Fools!!!!
L8tr
Enn[ Edited on 25/8/05 by tassupervee ]
Im not a complete idiot, quite a few parts are missing....
tassupervee wrote:I have one of those tools that Andy is selling.
It is an absolute MUST for any serious kraut builder. I bought it from the states a long time ago.
tell me how you are going to get the gland nut off an engine flywheel when the engine is on the floor and your mates are not around.
Tell me how you get that pesky axle nut off the old gearbox you found in the bush or the car is blocked up offen the ground and you dun have a m8 around to jam the brake pedal to the floor (assuming the brakes work at all)?
Thats right, you cant unless you have mates around or a gas axe handy.
This little gem gets them off without having to stop the engine or the axle from turning and you can use a 3/8" drive ratchet to do it.
No swearing and cursing, bashing the shit out of breaker bars and great chunk of steam pipe, engines leaping about all over the floor and the entire diff rolling along the floor as you madly chase it along all the while bashing the shit out of it.
The first time you do an axle nut up to 270 ft/lb you think you have stripped it it is sooo easy.
Stick your big sockets and bloody breaker bars and lengths of water pie and the rest of the garbage needed to hold the engine/axle down right up you arses.😁😁
This tool has paid for itself time and time again!!!!
I will rent you mine for 50 bucks LMAO, Fools!!!!
L8tr
Enn[ Edited on 25/8/05 by tassupervee ]
I agree, this is my favorite tool, it is so cool being able to undo the tightest flywheel nut with an 11mm ring spanner!!
FAHRVERGNUGEN;
Description of a pleasurable sensation,
Experienced when a car and it's driver are in mutual harmony, A unique driving experience, Pleasure, Satisfaction,
A feeling experienced by Volkswagen Drivers.
i used to sweat, swear, and get the shits big time untill i bought the tool, its not my fav tool, thats my business but its good all the same.
Andynn[ Edited on 25-8-05 by VolksFolks ]
They laugh because You are different, You laugh because They are all the same.
check out
www.lowlight.com.au for low lights only..
Who makes them
Ive got a 36mm sidchrome socket i bought 30 years ago... n a 3/4" breaker bar which i slip onto a bit of 4130 tube WORKS every time
how would that easy off work with deep dish off road wheels (i just wanto be able to take the drum off wheel and all)
atm i have to swap to a narrow wheel so the 36mm and 3/4" breaker can reach into the nut, block the wheel, support the outside end of breaker pivot and then bounce on the breaker arm.
if this thing fits within the dish of 15" wheels and allows the use of a 3/8 drive and extension (to clear the rim) and apply the torque, it sounds like the G.O.
:thumb
i've got a 36mm socket from a sunday 'trash n treasure' stall. Teamed with my 3/4 ratchet and an old axel tube, no one can stop me! Except if the engine is sittin on the garage floor...
...and Robert's ya father's brother...
so where do we get this yankie easy off tool - had a look on the volksfolks site, but couldn't see it there!
http://www.dtsband.com - Rock and Roll is NOT dead
My other car is a scooter, and it's in even more bits than my beetle. One day they will both be back together.......
Battyt batt, you can have the one here mate, seeing as nicko hasnt gotton back to me,
Andy
They laugh because You are different, You laugh because They are all the same.
check out
www.lowlight.com.au for low lights only..
I use a 3/4 rattle gun...but I'm lazy......:duh
tssnq.com.au
Sorry Andy I am holidays for a couple of weeks. Will contact you when I get back and organise something. Does it do 46mm nuts as well?
No Worries Nick, i will have more in a month, this perticular type is 36mm only, i do however stock 46mm EMPI clout breakers as below $29
i think i have 1 in stock too!
They laugh because You are different, You laugh because They are all the same.
check out
www.lowlight.com.au for low lights only..
