http://www.huv.com/jon/jeep/Welder/portable-welder.html
If anyone else has other methods, would be great.
I don't have a running engine, nor an alternator :P Hehe.
Got a BBQ, if that helps lol. As said to a few peoples, i am a nut case.
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears. 👍
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta!
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears. 👍
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta!
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears. 👍
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta!
I think its far easier to buy one....
As You can have enough trouble using a bought one....
The diodes in an alternator wouldn't last long iif You used one of those....
as electric welding is a "dead" short circuit.....
- Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY---
Haven't tried the Ozito/GMC small welders with small electrodes but for $99 they look a good alternative to the scraps in the above link you gave. Better get those guys on Home Improvements etc to teach you how to use it though! They seem to be able to do perfect welds after no practice! The real world just isn't that easy.
DH
cheers. where did u see these GMC ones?
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears. 👍
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta!
Both of these brands are in the Bunnings Warehouses Chris. As I said, I haven't used anything under 2.5mm rods in it. If I get time tomorrow I'll see if I can thieve a few 1.6mm rods from the welders and see how it runs them on 0.8mm sheet. One question! What are your welding skills like? It's easy for some of us to say how easy it is but one tends to forget that we learned to weld as kids and that was more years back than I'd rather remember! If you can handle the arc welder it's your cheapest option. I'm rather fortunate with my workplace as well as having all of that gear at home.
DH
Chris hasn't welded before.
-Staggers.
STAGGERS AUTOMOTIVE - Heavy Vehicle Diesel Specialist
JB CUSTOMS & CLASSICS - Car Builders
2/53 Tradelink Drive, Browns Plains
Good heavens! By the look of the rust in that thing he needs to dip it in a bath of lead to fill some of them rather than weld it up!
DH
[ Edited on 14/6/2006 by 1500S ]
A few years ago when i did my mechanic course we had to learn how to weld... i hated it... it was so hard to see what you were doing with the mask... and i just didn't have the confidence with that much power lol... needless to say i didn't finish the course...😢
I love welding! Pitty my own welder is only a small arc... But work has a massive 3 phase mig!!!
-Staggers.
STAGGERS AUTOMOTIVE - Heavy Vehicle Diesel Specialist
JB CUSTOMS & CLASSICS - Car Builders
2/53 Tradelink Drive, Browns Plains
Chris.
If you U2U me with your snail mail address I will send you a photocopy of an publication I have called, How to Build a High Voltage Power Plant and Welding Unit. I've never built one, but I bought the plans when I was a hippie on a hill and lived a long way from the power grid.
While I'm at it I'll also send you the plans for a Tesla Coil. Now that would be a lot of fun. I must build one one day. Either that or a Van der Graaf generator. Playing with electricity is one thing, but playing with lightning would be super cool.
Richard.
hey richard, my bro and i built a Van Der Graaf generator before, was wicked!
😀
Snail mail: 27 Duesbury Cres, Edenslanding 4207 QLD, or
mynameischris88@hotmail.com
Would be wicked mate if you could, but if its too much trouble, don't worry about it.
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears. 👍
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta!
dont use use an arc welder on ur body panels especially if u havent done much welding, u will just turn ur panels into swiss cheese. mig is way easier to use for welding thin metals. look on ebay i have seen migs there for very good prices
buy a going rego'd one that doesnt need a ton of welding.
I will be cheaper
This disclaimer does not reflect the thoughts or opinions of either myself, my company, my friends, or my dog: don't quote me on that; don't quote me on anything; this disclaimer is subject to change without notice; text is slightly enlarged to show detail; resemblance to actual persons, living or dead, is unintentional and coincidental; dry clean only; do not bend, fold, or mutilate; anchovies or jalapenos added to this disclaimer upon request; your mileage may vary; no substitutions are allowed; for a limited time only while supplies last; offer void where prohibited; this disclaimer is provided "as is" without any warranties expressed or implied
yeah, tis the other idea. i think it might be the case. What kinda $ value u rekon i would be looking at?
i can get around $500 for the baja project if i were to go buy another car that was running on the road.
But i don't know.
[ Edited on 14/6/2006 by bajachris88 ]
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears. 👍
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta!
