Skip to content
Aussieveedubbers

1200cc with period twin 28\'s..

0 likes
Share Share on Facebook Share on X Share on Reddit
Log in to reply

supercharged 66 Seriously Crusin Dubber

157 posts · joined Aug 2006 ·

#585669
Hi Guys, I have a couple of questions which I thought maybe someone out there has had seen or had carried out this type of buildup..

I am currently building up a standard 6 volt 1200cc stinker heater boxed motor. I have a set of aluminium cast intake manifolds, that run 28pic carbs. I have the linkage and all the necessary bits for it. I am going to run an old skool dunny roll ricoh oil filter. I have a period twin exhaust luckey which I want to run on it...

Questions.

1. Where is the best spot to tap into for the oil filter to run best?
2. any local suppliers for period style air filters, like the okrasa filters...52 mm diameter to fit on carbs...prefer removable which can be cleaned...
3. What would be best timing or advance to run the motor at?
4 Is it better to run an 8volt battery and upping the voltage regulator? anyone done this?
5. The carb intake manifolds dont have a breather pipe between them, would it run alot better with a breather connecting the two?

If anyone has run this type of motor with this carb setup any info would be greatly appreciated...cheers
zsolt brisbane..

squizy Thinking about another dub...maybe

4,082 posts · joined Dec 2002 ·

#585706
There's a good post going on The Samba in regards to this. Been keeping an eye on it myself.

http://www.thesamba.com/vw/forum/viewtopic.php?t=96565&start=200

Also Craig Torrens has a little surprise in his '54 that you may be interested in. Have a search for some posts from Craig re this, unless he's around to be able to add something into this thread.

1500S Custom Title Time!

1,418 posts · joined Mar 2005 ·

#585783
The twin carbs you have were common during the 60s on 1200 engines and worked well. No, they didn't usually run the balance pipe.

8 volt batteries were also used back then. The local (at Blacktown) battery supplier was Pope Batteries and they supplied quite a few around the area with very few reported problems.

DH

supercharged 66 Seriously Crusin Dubber

157 posts · joined Aug 2006 ·

#585835
Thanks 1500s, I am bit hesitant to drill holes in the inlet manifolds. I did have a look at the samba to see if anyone has a similar project...not a great deal of pics though...If anyone has an old publication or reference material showing some pics this would help as well...cheers zsolt brisbane..

kombikim disfunctionally capable

1,521 posts · joined Dec 2002 ·

#585836
non of the ones I ever saw had a balance tube, please note that they are called balance pipe, or balance tube, not breather pipe which is a completely different thing altogether, & the ignition timing setting depends on too many factors, you will just have toi wait until you get it going to work that out.
Please, I need drivers side window regulator (winder mechanism) for my '54

supercharged 66 Seriously Crusin Dubber

157 posts · joined Aug 2006 ·

#585933
cheers guys, thanks for the help..zsolt..

Craig Torrens 6 times Australian, 7 times State Hillclimb Class Champion

8,040 posts · joined Jan 2003 ·

#585947
I run the setup on my 36hp. Use a balance tube.:thumb


vw54 Administrator Always Waiting 4 Friday

16,723 posts · joined Aug 2002 ·

#585977
Zsolt

1. Where is the best spot to tap into for the oil filter to run best?

the best place for the out take is of the oil pressure switch you can buy a adaptor fitting to mount the existing pressure switch and use the other side as an exit to the filter the return line is in the stud that holds the distributor in place it has to be drill out. Okrasa engines did it this way


3. What would be best timing or advance to run the motor at?

this will have to adjusted when you have the carbies set upjust stop it pinging


5. The carb intake manifolds dont have a breather pipe between them, would it run alot better with a breather connecting the two?

You have the alloy mainifolds which didnt use a balance line it creates a lot more stuffing around this way The Ken Virgin steel mainfolds i have and have used run a balance line and make the tuning much easier and smoother

I have nearly finished my set up for my 1200 Sea Blue conversion will be fitting it soon, together with all the other hot up bits n wheels
I read it on FACEBOOK so it must be true


http://forums.aussieveedubbers.com/viewtopic.php?tid=91278&page=1#pid848630


http://forums.aussieveedubbers.com/viewtopic.php?tid=63561&page=1#pid624099


http://forums.aussieveedubbers.com/viewtopic.php?tid=4832&page=1#pid452603


http://forums.aussieveedubbers.com/viewtopic.php?tid=60650&page=1#pid574409

supercharged 66 Seriously Crusin Dubber

157 posts · joined Aug 2006 ·

#586108
vw 54, could you post some pics please!
Craig, love your oval, I had a 54 some years ago...dont slam it...leave it crusty man...she is sweet..I have a 66 beetle which is original and crusty....which down the track I have a judson to go on....but for the moment this 1200 setup is destined for my ghia vert...I have the alloy manifolds like yours Craig...any more close up pics would be great! Do you know who made these manifolds? glad to see some other dudes fiddling around on these types of setups.... keep the info coming much appreciated...cheers.zsolt.

oldspeed....man there is a beautiful dove blue, 53 barndoor, judson blown panel on the samba...puch in barndoor and check thru the adds...she is there.....someones labour of love....

[ Edited on 19-4-2007 by supercharged 66 ]

LUFTMEISTER Veteran Volks Folk

2,041 posts · joined Jul 2005 ·

#586113
Stop mucking around and put a Subi in it.......you know you want too!
Don't deny the force Luke.😂
Customer service is not dead in Australia.

Always after HAZET & MATRA & VW factory tools

Craig Torrens 6 times Australian, 7 times State Hillclimb Class Champion

8,040 posts · joined Jan 2003 ·

#586254
yawn


supercharged 66 Seriously Crusin Dubber

157 posts · joined Aug 2006 ·

#586293
no subi thanks.

whatnow Custom Title Time!

1,000 posts · joined Jan 2003 ·

#587248
i think the manifolds craig is using came out of a kit made in melbourne back in the day. sorry i can't remember the name.

i still curse myself for letting them go.

Craig Torrens 6 times Australian, 7 times State Hillclimb Class Champion

8,040 posts · joined Jan 2003 ·

#587493
whatnow wrote:i think the manifolds craig is using came out of a kit made in melbourne back in the day. sorry i can't remember the name.

i still curse myself for letting them go.
Its probably better they are being used and not collecting dust somewhere:thumb

[ Edited on 26-4-07 by Craig Torrens ]