Skip to content
Aussieveedubbers

Lift spindles in Australia?

0 likes
Share Share on Facebook Share on X Share on Reddit
Log in to reply

General_Failure Use your head, don't abuse it!

1,036 posts · joined Jun 2004 ·

#680772
G'day.

Just wondering if lift spindles are legal here? I want them for my bay, or the torsion bar adjuster or something. I don't actually care about it being adjustable. I just want to take it up, and stay somewhere near road legal.

I know I've posted on this in the past, but my project is starting to take shape in a backyard mechanic style beer, music and tools kind of way. It'll always be a rat as it had a hard life and the original 70's camper conversion was pretty bodge, so I'm just saying to hell with originality and doing things my way.

I do want to use it for camping and travelling, suited to me so a lift is really pretty necessary. I think I can get away with lifting the rear a little and putting some nice big wheels on the back, but we all know how small the arches for the front are.
If at first you don't succeed. Build, build again.
Vehicle: 1975 Special order delivery walkthrough panel based LCA pop-top camper. Motor: Nippon 1.8L Single port Wasserboxer, Transmission: 3 rib 002.

General_Failure Use your head, don't abuse it!

1,036 posts · joined Jun 2004 ·

#680794
Wow. Thanks!

Where does the lift come from in the baja beam?

And what benefit does it have over an adjustable beam where the price comes out about even. Not defending any particular type. Just trying to understand what's out there and the pros / cons.
If at first you don't succeed. Build, build again.
Vehicle: 1975 Special order delivery walkthrough panel based LCA pop-top camper. Motor: Nippon 1.8L Single port Wasserboxer, Transmission: 3 rib 002.

Brad Wolfsburg Elder

3,764 posts · joined Aug 2002 ·

#680802
The lift in the CVD Beam is from th e12mm drop plates welded to the mounting points which allow you to fit it 3" lower thus raising your bus. These beams alos have adjusters for height and adjustable bump stops.

The beaty of them is that you can drop them up or down to suit. They were making them at 2", 3" and 4" on the one beam so you could pick your height.

If you wanted one without adjusters I am sure they would drop about $300 - $350 in price.
Brad
Why copy when you can own an original ?
Meyers Manx Australia

General_Failure Use your head, don't abuse it!

1,036 posts · joined Jun 2004 ·

#680860
So they adjust too? Very nice. Couldn't tell what was going on in the pic too well with all the black on black.

What allowances have to be made for steering when doing this? Realignment for height change, elongated rods, different rods for different heights?

Teach me, Master!
If at first you don't succeed. Build, build again.
Vehicle: 1975 Special order delivery walkthrough panel based LCA pop-top camper. Motor: Nippon 1.8L Single port Wasserboxer, Transmission: 3 rib 002.

Brad Wolfsburg Elder

3,764 posts · joined Aug 2002 ·

#680861
General_Failure wrote:So they adjust too? Very nice. Couldn't tell what was going on in the pic too well with all the black on black.

What allowances have to be made for steering when doing this? Realignment for height change, elongated rods, different rods for different heights?
Adjust too - Yes

Picture is a car part not a fashon shoot.

Steering does not change as uch. You dog leg your idler shaft and cut the bottom off the cross member where it currently passes through. As it is jointed both ends with an idler on the beam there are no issues at all.

So in summary if you bought one of these beams then you could pull yours off, bolt this one on, dog leg your idler shaft and bolt your arms etc on and walla up to about 5 " of lift if you want it. Enough to clear 31 x 10.5 x 15 inch tyres. Although most only go 235 x 75 x 15 as with the 31's steering is a biatch
Brad
Why copy when you can own an original ?
Meyers Manx Australia

General_Failure Use your head, don't abuse it!

1,036 posts · joined Jun 2004 ·

#680864
Heh. Yeah I know it's not a fashion shoot 🙂 Nice looking beam though. Might have a career in modelling.

what method is used to put the dog leg in?

Just went hunting because I couldn't really visualise the 31x10.5x15 tyres. Those things are massive! Can't say I'm surprised there are steering issues.

Still need to find a set of 15" rims too. Victoria is pretty dry for merc parts.

Thanks for all the info.
If at first you don't succeed. Build, build again.
Vehicle: 1975 Special order delivery walkthrough panel based LCA pop-top camper. Motor: Nippon 1.8L Single port Wasserboxer, Transmission: 3 rib 002.

philsmanx Officially Full-On Dubber

286 posts · joined Nov 2008 ·

#687893
the guy at sharpbuilt does these droped spindles 3 inches he tells me and they have brackets for disk brakes not sure on cost contact him
on the rebuild ej25 monster bug on the way