Skip to content
Aussieveedubbers

For those who are running adj. struts

0 likes
Share Share on Facebook Share on X Share on Reddit
Log in to reply

alien8 Wolfsburg Wizard

521 posts · joined Sep 2008 ·

#681306
Where did you relocate the flexible brake hose mounting bracket? Its looking a little tight to mount it in a similar position on the adjustables.

Brad Wolfsburg Elder

3,764 posts · joined Aug 2002 ·

#681309
I have MaXX Struts from topline and they come with a bolt on bracket to suit the application.

I will be selling these in the near future if that helps.
Brad
Why copy when you can own an original ?
Meyers Manx Australia

alien8 Wolfsburg Wizard

521 posts · joined Sep 2008 ·

#681349
Buggy Brad wrote:I have MaXX Struts from topline and they come with a bolt on bracket to suit the application.

I will be selling these in the near future if that helps.
The brackets or the struts?

I contacted Topline about their adjustables but I ended up going with the Empi adjustables and inserts. If the $A was like it was 6 months ago I would of bought Topline but the Empi's were just way cheaper. You do hear a lot of good things about the Topline gear though. I would really like their caster-fix bushes and a camber/control arm kit.

Brad Wolfsburg Elder

3,764 posts · joined Aug 2002 ·

#681352
Both, what do the empi struts look like ? What were the worth ?
Brad
Why copy when you can own an original ?
Meyers Manx Australia

alien8 Wolfsburg Wizard

521 posts · joined Sep 2008 ·

#681365
These are the Empi's except I got the 3 bolt 1302's.
$170 for the strut pair and
$80 each for the inserts.

I am intrested in the brackets. Do they mount around the strut tube?

1 attachment · Log in to view

1303Steve Scirocco Rare

8,650 posts · joined Aug 2002 ·

#681397
Hi

So do they still use the big springs on the empi struts? On my V force struts I just welded the old tab in a suitable position.

Steve

alien8 Wolfsburg Wizard

521 posts · joined Sep 2008 ·

#681403
1303Steve wrote:Hi

So do they still use the big springs on the empi struts? On my V force struts I just welded the old tab in a suitable position.

Steve

Yeah, just the stock's but I think you can get lowered coils for them to.

With the adjustables on the lower setting there's not much room to weld the tabs on ,or what I should say is there's not enough room to bend the flexible brake hose under the lower perch.

vw54 Administrator Always Waiting 4 Friday

16,723 posts · joined Aug 2002 ·

#681416
I think you will have a few problems with the EMPI strut housings
I read it on FACEBOOK so it must be true


http://forums.aussieveedubbers.com/viewtopic.php?tid=91278&page=1#pid848630


http://forums.aussieveedubbers.com/viewtopic.php?tid=63561&page=1#pid624099


http://forums.aussieveedubbers.com/viewtopic.php?tid=4832&page=1#pid452603


http://forums.aussieveedubbers.com/viewtopic.php?tid=60650&page=1#pid574409

Bizarre Moderator The artist formerly known as blue74l

12,789 posts · joined Aug 2002 ·

#681467
Its not lowered springs you are after - it is thinner

They have a fat base - so they take stock springs.
All you will do is lower your beetle for $170+$80*2=$330

Now - This is CHEAP compared to a beam

The best you can do now is try and get hour glass springs
This will allow you to run a wider wheel that doesnt foul the spring

The benefit of a strut (like V Force - which i have) is you can run wider wheels.

The springs are going to cost another $100 US http://www.toplineparts.com/frameset.html
This is ....$150 + post
Say $300 landed
That is $650 and inferio to a V Force style strut
Cheaper but no where near as good

I am running a 205 wheel with a 50ET
Rekon this is too much by 15mm
With the right ET wheels and maybe rolling the lip i reckon i would get a 225 under a stock guard
Futue te ipsum!!!

Joel Now containing 100\% E-Wang

9,368 posts · joined Feb 2006 ·

#681472
those empi ones are just a copy of toplines versa-strut but would be made thinner metal and sweatshop welding jobs

u can make narrow coils out of them but as Barry said they wont be as good as richards

if u need narrow spring struts on the cheap what u can try is the rear springs and retainers from an EF Civic hatch or CRX thats 88-91 models

the spring is only about 80mm vs superbug 120mm
the honda top rubber spring holder sits neatly in the bottom spring cup on superbug struts and the bottom honda spring cup welds to the upper vw spring holder

not a pretty solution but it works with stock struts so i assume it would with those empi struts
i havent tried it but know a few ppl that have

alien8 Wolfsburg Wizard

521 posts · joined Sep 2008 ·

#681478
vw54 wrote:I think you will have a few problems with the EMPI strut housings

Can you elaborate?

They do look like a copy of the Topline Versa struts.

I am running 165 15's so I don't need a smaller diameter coil, but new coils would be stellar. I just need to relocate the brake line.

Bizarre Moderator The artist formerly known as blue74l

12,789 posts · joined Aug 2002 ·

#681482
"My" concern with these is i "think" the coil cup is held in place with a circlip??

Correct me if i am wrong

I dont understand the bkake clip question

Mine is in the same place
No problem

If you have 3 bolt bases they are better in the sense they are not cut
Again "my" concern with the way some people do 2 bolts is cutting and welding the tube on the clamp
V Force bore the original clamp amd slide the existing tube down and then weld it
Futue te ipsum!!!

alien8 Wolfsburg Wizard

521 posts · joined Sep 2008 ·

#681483
Bizarre wrote:Its not lowered springs you are after - it is thinner

They have a fat base - so they take stock springs.
All you will do is lower your beetle for $170+$80*2=$330

Now - This is CHEAP compared to a beam

The best you can do now is try and get hour glass springs
This will allow you to run a wider wheel that doesnt foul the spring

The benefit of a strut (like V Force - which i have) is you can run wider wheels.

The springs are going to cost another $100 US http://www.toplineparts.com/frameset.html
This is ....$150 + post
Say $300 landed
That is $650 and inferio to a V Force style strut
Cheaper but no where near as good

I am running a 205 wheel with a 50ET
Rekon this is too much by 15mm
With the right ET wheels and maybe rolling the lip i reckon i would get a 225 under a stock guard
Ok, I get it now . Dam! I had to read that a few times.
I didn't factor in new coils as I was going to use the old stock one's with the Empi struts.

How much is a V force setup for adjus. struts, inserts and coils?

Bizarre Moderator The artist formerly known as blue74l

12,789 posts · joined Aug 2002 ·

#681484
These are V Force 3 bollters

Futue te ipsum!!!

Bizarre Moderator The artist formerly known as blue74l

12,789 posts · joined Aug 2002 ·

#681485
Best to call Richard on 0408 991 247
Starts around a grand and goes up depending on what you want
Futue te ipsum!!!

alien8 Wolfsburg Wizard

521 posts · joined Sep 2008 ·

#681487
Bizarre wrote:"My" concern with these is i "think" the coil cup is held in place with a circlip??

Correct me if i am wrong

I dont understand the bkake clip question

Mine is in the same place
No problem

If you have 3 bolt bases they are better in the sense they are not cut
Again "my" concern with the way some people do 2 bolts is cutting and welding the tube on the clamp
V Force bore the original clamp amd slide the existing tube down and then weld it
Yes, the perches are held in place with a circlip. I dont know about this? But I was a little shocked when I first saw how the perches are held in place. Hey, I got them mail order, Ive never seen them prior to this. Hmm Empi.

As for the brake thing. I am asking where to put the flexible brake hose mount as there is not enough room to mount it on the strut tube below the adjustable perch.

alien8 Wolfsburg Wizard

521 posts · joined Sep 2008 ·

#681490
Bizarre wrote:These are V Force 3 bollters

Arrr, the difference with these is the lower perch is alot smaller than the Empi's hence the reason the V force don't have clearence issues with the flexible brake hose. It was doing my head in why I seem to be the only one with this problem.

barls Administrator Causer of Chaos and Mayhem

9,473 posts · joined Jun 2004 ·

#681491
can highly recommend the v force ones as they are what i upgraded to from my lowered stock struts
“We all pay for life with death, so everything in between should be free.” Bill Hicks
the chaos project - click me

Brad Wolfsburg Elder

3,764 posts · joined Aug 2002 ·

#681497
mmmm interesting read. I looked at going with the V Force struts and the end result was I buoght MaXX Struts and now I am importing then from Topline as I was very happy with them as far as value for money and service went. A pair of MaXX struys complete will set you back $795 for the 3 bolt units to suit you car. These have an 80mm coild and allow plenty of clearance for larger tyres.

I will get some pictures posted of them. They use a clip to hold the lower perch in place like the empi ones. This is then covered with the tappered bottom perch making it impossible for it to come off. The only draw back of this design compared to the style V-Force sell is that you need to drop the strut top out to adjust them up and down. With the thread type you can just jack the car up and you get more finite settings as you car turn the mount up and down as opposed to the clip style which restricts you to 12mm incriments.

That being said have a look around at the comments on the MaXX struts. I haven't seen anyone with any issues yet. Also have a look around at the V-Force ones and see what people say.

I think you are on a winner either way. In fact stock ones cut and welded are better than Empi crap.

I will also post some pictures of the brake line retainers, the clip onto the bottom leg and have a bolt holding them in place.
Brad
Why copy when you can own an original ?
Meyers Manx Australia

Bizarre Moderator The artist formerly known as blue74l

12,789 posts · joined Aug 2002 ·

#681502
Buggy Brad wrote:The only draw back of this design compared to the style V-Force sell is that you need to drop the strut top out to adjust them up and down. With the thread type you can just jack the car up and you get more finite settings as you car turn the mount up and down as opposed to the clip style which restricts you to 12mm incriments.
mmm sort of agree

To me the adjustment comes by changing the springs
I like to see the spring held when on full travel - ie jack the car up and the sprin is held. Not loose.
I "think" i have a 10" spring in there at the moment with a helper spring.
The helper squashes to about 1 or 2 inches
I have seen flat helpers that squash to 1/4"
I dont like just lowering the perch/cup as i get concerned the spring can unseat on a decent speed bump

Maybe worry too much

comments??
Futue te ipsum!!!

Bizarre Moderator The artist formerly known as blue74l

12,789 posts · joined Aug 2002 ·

#681507
Brad

The only info i have is from SBO
My only comment on Maxx is in the way the insert is held.
Supe talks of wrapping a leather belt bit around the insert to hold it?? Comments??
$$$ they are VERY good value

What inserts do they come with??
Boge??

I have always been shot down when trying to find out what spring rating they come with
My V Force are 130lbs??
the SBO boys seem to think this is WAY over and should be 60 or 80
When Richard spoke to .....mmm forgot name - Mr Topline... they agreed to differ.
They measure different over there
Richard generally uses King springs and take the ratings from their data sheets
Futue te ipsum!!!

grumble Son of Jim - Creator of Good

2,672 posts · joined Jun 2008 ·

#681515
I say you can't beat dealing with a local because if there is a problem down the line he will look after you,try doing this with someone from overseas and see how the system works. I have no problems with dealing with guys like Richard from V Force because he will give you as much information as he can regardless whether he sells the bits or not. An even better reason is he supports the local VW scene. Les

alien8 Wolfsburg Wizard

521 posts · joined Sep 2008 ·

#681517
Ok now I am really spewing I got the Empi's.
Should I be really worried that these thing are going to bend or snap?

Brad Wolfsburg Elder

3,764 posts · joined Aug 2002 ·

#681548
grumble wrote:I say you can't beat dealing with a local because if there is a problem down the line he will look after you,try doing this with someone from overseas and see how the system works. I have no problems with dealing with guys like Richard from V Force because he will give you as much information as he can regardless whether he sells the bits or not. An even better reason is he supports the local VW scene. Les
I am glade to hear you had good experiences, there are more than a few on here who have not and will never shop local for superbug parts again. I myself am one of these which is why I started looking at the toplone stuff.

Bizarre, I hear what you are saying about colis and mounts but if you have a look at a lot of strut / coil cars this is not the case. The coils in my Landcruiser for example pretty much fall out when you put it on the hoist. In relation to a lowered bug with adjustable struts where the lower perch has been moved down to reduce ride height, I agree as you reduce the pre load you increase the chance of the spring poping off as such and rising up onto the lip of the lower mount. Spring retainers remove this as an issue and are supplied with the kits I will be selling.

With the technology out there these days in spring world a progressive spring which is correctly rated is pretty easy to come by and not real expensive. I am currently talking to a local spring company to do just this with a flexy or variable rate coil to suit. I should have these availible about 2 or 3 mths after I finish my L Bug as I need a better test rig to give them abuse to proof the design idea and rate specs.
Brad
Why copy when you can own an original ?
Meyers Manx Australia

alien8 Wolfsburg Wizard

521 posts · joined Sep 2008 ·

#681550
Sounds pretty good Brad. I will be needing new coils in a couple of months. Will you be stocking the swaybar castor bushes and camber bushes that Topline offer?

vw54 Administrator Always Waiting 4 Friday

16,723 posts · joined Aug 2002 ·

#681563
Whats wrong with the Empis same as nearly all the empi products they dont work or leak or are missing a part like the brake clip or the strut towers
I read it on FACEBOOK so it must be true


http://forums.aussieveedubbers.com/viewtopic.php?tid=91278&page=1#pid848630


http://forums.aussieveedubbers.com/viewtopic.php?tid=63561&page=1#pid624099


http://forums.aussieveedubbers.com/viewtopic.php?tid=4832&page=1#pid452603


http://forums.aussieveedubbers.com/viewtopic.php?tid=60650&page=1#pid574409

Joel Now containing 100\% E-Wang

9,368 posts · joined Feb 2006 ·

#681570
supers have naturally long springs compared to other cars

even when mine was 45mm off the ground running lowest setting with .......cough...... cut springs.... it wasnt even close to being loose in the cups when jacked up

u would need to chop alot out b4 being loose would be a problem and bigger problem than that would be they wouldnt seat properly in the cups

have a read of

http://www.thesamba.com/vw/forum/viewtopic.php?t=329584

guy from SBO runs them and his super is stupidly low too

a good point was made:
EMPI has sold a bunch of their adjustable struts, and I've never heard of them breaking. We all know that if it did happen, it would be plastered all over this site.

Bizarre Moderator The artist formerly known as blue74l

12,789 posts · joined Aug 2002 ·

#681603
Joel wrote:even when mine was 45mm off the ground running lowest setting with .......cough...... cut springs.... it wasnt even close to being loose in the cups when jacked up
.
The difference is the stock spring is under compression when bolted together "i believe"
Hence the need for clamps when you pull them apart

This is not the case with my V Force struts
The spring is in a natural state when at rest

So at full jacking the stock spring is still in compression where as mine is not
So ANY lowering of the cup loosens the spring
Futue te ipsum!!!

Brad Wolfsburg Elder

3,764 posts · joined Aug 2002 ·

#681604
Bizarre wrote:
Joel wrote:even when mine was 45mm off the ground running lowest setting with .......cough...... cut springs.... it wasnt even close to being loose in the cups when jacked up
.
The difference is the stock spring is under compression when bolted together "i believe"
Hence the need for clamps when you pull them apart

This is not the case with my V Force struts
The spring is in a natural state when at rest

So at full jacking the stock spring is still in compression where as mine is not
So ANY lowering of the cup loosens the spring
The MaXX Struts are the same. When you lower then the spring flopes around
Brad
Why copy when you can own an original ?
Meyers Manx Australia