Skip to content
Aussieveedubbers

Smokin 64 Beetle

0 likes
Share Share on Facebook Share on X Share on Reddit
Log in to reply

64blackbettle Commited Dubber

51 posts · joined Mar 2012 ·

#892006
Hi All, I've just purchased a 64 Beetle and need some wiring done. When I turn the lights on wires start to smoke and get a little hot. I'll put up a slab for your help or I'll even part with the stuff that folds...if I must. Anyway, if you're in Melb and can give a fellow new bugger a hand that would be great. Give me a buzz or PM me if you can help. Thanks everyone Dom 0418 133 580

3 attachments · Log in to view

vlad01 Compulsive Aussie Vee Dubber

4,270 posts · joined Jun 2010 ·

#892015
🤪

71 notchback,
Past owner of, 70 NB, 73 SB and 72 FB TLE

greedy53 Bishop of Volkswagenism

3,062 posts · joined Mar 2006 ·

#892495
get someone to turn the ting on while u watch and try and find the point where smoke starts and make sure all open joiners are taped and there are no shorts
good luck
👍👍😂🙅🥷😬🤓

vwo60 Veteran Volks Folk

2,036 posts · joined Feb 2007 ·

#892505
Looks like a artisan wired it, you will need a wiring diagram so you can trace the wiring and see what works and what does not.

Lucky Phil Wolfsburg Wizard

480 posts · joined Aug 2010 ·

#892526
Boy, that's a mess!
I like the shot of the workshop through the dash.
This is no job for a beginner methinks.
Someone with a few wiring skills should be able to do a basic tidy up fairly quickly.

hellbugged 48's and straight cuts

5,080 posts · joined Apr 2003 ·

#892535
Needs a major re think that wiring,

It's not too difficult, but takes time and patience

64blackbettle Commited Dubber

51 posts · joined Mar 2012 ·

#892681
Lucky Phil wrote:Boy, that's a mess!
I like the shot of the workshop through the dash.
This is no job for a beginner methinks.
Someone with a few wiring skills should be able to do a basic tidy up fairly quickly.
Perfectly planned shot of the workbench. I've managed to pull down the mess this was the wiring and label everything...my way. I can now see the light thru the fog and isolated the main wiring harness, which should make life a little easier. I think I'll start with the lights and work my way to the ignition.

The melted wire was an ignition wire. Looked very thin. So I replace that with a properly rated wire.

Can some one tell what the white thing is with wires connected to it? It looks like an old house fuse with wiring from the wiper switch going directly into it.

2 attachments · Log in to view

64blackbettle Commited Dubber

51 posts · joined Mar 2012 ·

#892692
That white thing isn't connected to the wiper switch. There's a thick RED wire coming out of it and going straight to the fuse box and back into the ignition switch

ducati998 Commited Dubber

53 posts · joined Apr 2010 ·

#892726
The white things are ballast resistors. They drop the nominal battery voltage down to approximately half its value. They use resistors in older VW's so you can still run a 6 volt wiper motor but use a 12 volt battery system.

Cheers

Jason

ClockworkMonkey Seriously Crusin Dubber

199 posts · joined Oct 2009 ·

#892731
Was the car working with the wiring like that? Looks like a very special person put that in :-)

Joel Now containing 100\% E-Wang

9,368 posts · joined Feb 2006 ·

#892759
No wonder you were getting dead shorts, alot of live uninsulated connectors there.


Charge light socket laying there loose with no bulb would have been playing games with the charging system too.

64blackbettle Commited Dubber

51 posts · joined Mar 2012 ·

#892770
ducati998 wrote:The white things are ballast resistors. They drop the nominal battery voltage down to approximately half its value. They use resistors in older VW's so you can still run a 6 volt wiper motor but use a 12 volt battery system.

Cheers

Jason
Jason, would you recommend replacing the 6v wiper motor with a 12v motor to keep voltage consistant across the car. Or leave it as is?

hellbugged 48's and straight cuts

5,080 posts · joined Apr 2003 ·

#892772
few options with the wipers. new 12v armature can go in the motor itself, or new style reistors/voltage drop units are readily available (drop power from 12 to 6 to the wiper motor)

that wiring looks better already 😉

bajachris88 The international telephone dialing code for Antarctica is 6

6,661 posts · joined Apr 2005 ·

#892775
my light switch used to smoke when wired incorrectly.

Particularly smoke when i would adjust the dimmer. i had the headlights on the dimmer side, and the dimmer on the headlights wire...

So all in all, i had adjustable dimming headlights lol.
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears. 👍
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta!

64blackbettle Commited Dubber

51 posts · joined Mar 2012 ·

#892776
hellbugged wrote:few options with the wipers. new 12v armature can go in the motor itself, or new style reistors/voltage drop units are readily available (drop power from 12 to 6 to the wiper motor)

that wiring looks better already 😉
I've seen new 12v armatures being installed on youtube. I think i might go down that path. Cheers

ducati998 Commited Dubber

53 posts · joined Apr 2010 ·

#892811
64blackbettle wrote:
hellbugged wrote:few options with the wipers. new 12v armature can go in the motor itself, or new style reistors/voltage drop units are readily available (drop power from 12 to 6 to the wiper motor)

that wiring looks better already 😉
I've seen new 12v armatures being installed on youtube. I think i might go down that path. Cheers
Installing a 12v armature eliminates the need for resistors.
Which means less connections in the circuit.
Which means less chances of problems.
So it's got to be better. 😂

64blackbettle Commited Dubber

51 posts · joined Mar 2012 ·

#892837
ClockworkMonkey wrote:Was the car working with the wiring like that? Looks like a very special person put that in :-)
It was working OK, but things started to go smokiel when I switched the lights on

Joel Now containing 100\% E-Wang

9,368 posts · joined Feb 2006 ·

#892852
If your not worried about originality you could always fit a later 12 volt beetle wiper motor and switch.

Atleast then you would get 2 speeds and not have to deal with those crappy light weight 6 volt wiper arms anymore.

64blackbettle Commited Dubber

51 posts · joined Mar 2012 ·

#892871
The 12v option sounds like the way to go. Where's the best place to pick one up from?

The wiring is at least now organised into logical groups. The main loom top right, and the bottom left is for the lights. Now I just need to add the bits in the middle and I'm done....I hope.

I'll head over to the Auto Elec this weekend and pick up the right sort of wires for the job and some advice and I'll give it a crack at some stage.

3 attachments · Log in to view