Droopy Semaphore

Moosey Learner Dubber

11 posts · joined Apr 2014 · 4 May 2014, 8:33 pm

#990087

Can anyone help me with my early 60 Beetle semaphore indicator ,like many of us over 50s my left indicator will not raise up that last inch (25mm). All advice appreciated.

vw54 Administrator Always Waiting 4 Friday

16,723 posts · joined Aug 2002 · 5 May 2014, 7:26 am

#990119

Remove from the car remove the lens plastic, bulb

give a good wash out in petrol or kero open the arm when washing to remove dirt from the solinoid rod

blow off with air scrap the gunk of the electrical terminal

you can coat the coil with a laquer if you want

I read it on FACEBOOK so it must be true

http://forums.aussieveedubbers.com/viewtopic.php?tid=91278&page=1#pid848630

http://forums.aussieveedubbers.com/viewtopic.php?tid=63561&page=1#pid624099

http://forums.aussieveedubbers.com/viewtopic.php?tid=4832&page=1#pid452603

http://forums.aussieveedubbers.com/viewtopic.php?tid=60650&page=1#pid574409

Moosey Learner Dubber

11 posts · joined Apr 2014 · 5 May 2014, 6:57 pm

#990160

Thanks for that I will give it a go this weekend. Fingers crossed

Moosey Learner Dubber

11 posts · joined Apr 2014 · 6 May 2014, 7:34 pm

#990228

OK Did all that and I have a lovely clean semaphore that still stops a little short of the mark (same as before clean). Is there any thing else I could try?

vw54 Administrator Always Waiting 4 Friday

16,723 posts · joined Aug 2002 · 6 May 2014, 8:22 pm

#990234

check all the terminal contacts and make sure you have a good charged battery
especially check the earth points on the car

I read it on FACEBOOK so it must be true

http://forums.aussieveedubbers.com/viewtopic.php?tid=91278&page=1#pid848630

http://forums.aussieveedubbers.com/viewtopic.php?tid=63561&page=1#pid624099

http://forums.aussieveedubbers.com/viewtopic.php?tid=4832&page=1#pid452603

http://forums.aussieveedubbers.com/viewtopic.php?tid=60650&page=1#pid574409

AA003 Custom Title Time!

1,189 posts · joined Oct 2011 · 6 May 2014, 8:40 pm

#990236

Moosey wrote:OK Did all that and I have a lovely clean semaphore that still stops a little short of the mark (same as before clean). Is there any thing else I could try?

Viagra

I read it on samba, so it must be correct.

Sometimes Volkswagen dealers sell spare parts. Amazing isn't it!😂

Moosey Learner Dubber

11 posts · joined Apr 2014 · 6 May 2014, 10:13 pm

#990241

right one works fine so the problem is only with the left one.

gordysbeetle Seriously Crusin Dubber

125 posts · joined Jun 2011 · 7 May 2014, 4:59 pm

#990290

AA003 wrote:
Moosey wrote:OK Did all that and I have a lovely clean semaphore that still stops a little short of the mark (same as before clean). Is there any thing else I could try?
Viagra

I was thinking the same thing. only problem is it wont go down for 3 or 4 blocks 😂😂😂

Moosey Learner Dubber

11 posts · joined Apr 2014 · 7 May 2014, 7:26 pm

#990302

OK I finally fixed the semaphore. I decided to swap over left indicator with the right one ,while they were both out I compared the two even though they were different models (C and E after numbers) they are very similar . The problem was that someone had done a dodgy repair using a split pin at the connection at the top of the cylinder and link to the indicator physically stopping the piston mech from going all the way down. I replaced this with a small section of a pop rivet shaft slightly flattened at one end put them back and bingo they are both going up all the way. No Viagra required but one happy veedubber regardless.
Thanks All