Skip to content
Aussieveedubbers

4 cars in one

0 likes
Share Share on Facebook Share on X Share on Reddit

lakey Casual Dubber

44 posts · joined Jul 2010 ·

#994362
My name is Paul from Brisbane Iam building a beetle.
It consists of
64 beetle body
76 beetle pan and irs gearbox
Porsche 944 brakes and
a Subaru 2.2 n a motor.

But Ive hit a few little snags could any body help 🥲

Thanks Paul

HappyDaze Superannuated

2,887 posts · joined Jun 2009 ·

#994363
Victor Frankenstein, perhaps ?😉
I'd rather wear a Beetle out by racing it than by polishing it!

Doug Sweetman Nil Bastardo Carborundum

2,128 posts · joined Sep 2002 ·

#994374
That'll be a sweet package when finished !! There are a couple of blokes on here with the 944 brake experience and a bunch with subie experience so you have come to the right place.

lou0060 Wolfsburg Wizard

568 posts · joined Dec 2010 ·

#994570
always keen for a snag or two...

what's the problem Paul??
1971 karmann ghia Cabrio - Cruising 👍
1963 beetle Sunroof - gathering dust 🥲
1968 race beetle - twin turbo Subaru - stress relief 😁
1960 beetle - old school low & slow 😏

1303Steve Scirocco Rare

8,650 posts · joined Aug 2002 ·

#994598
ask away

lakey Casual Dubber

44 posts · joined Jul 2010 ·

#994965
No 1 the floor pan is IRS disc brake ball joint front beam. The IRS single sideplate gearbox doesn't fit properly onto the chassis. The original gearbox mount on the body had already been taken off. Do I have to make a special mount to connect them together.
Thanks lakey

Joel Now containing 100\% E-Wang

9,368 posts · joined Feb 2006 ·

#994969
There's no gearbox or engine mounts on the body, just the front nose cone mount and the rear gearbox cradle bolted to the chassis forks.

is your front mount what your talking about?

the 73-76 pans have a totally different front setup, theres no mounting bracket like the pre 72 just 2 studs hanging down that pick up the gearbox nose cone rubber mount

lakey Casual Dubber

44 posts · joined Jul 2010 ·

#995019
Hi

The front gearbox nose cone mount hits the tube that go out to the spring plates. The gearbox seems to be leaning down towards the front. Any ideas , does this make sense.

Thanks Paul

Joel Now containing 100\% E-Wang

9,368 posts · joined Feb 2006 ·

#995024
If the nose cone is hitting the Torsion bar tube sounds like you have the gearbox cradle back to front, there is normally a 2" gap between the tube and the nose cone.

lakey Casual Dubber

44 posts · joined Jul 2010 ·

#995034
Hi

Is the cradle for a sixties car different to a seventies one. I think i have a sixties one on .

Thanks Paul

Joel Now containing 100\% E-Wang

9,368 posts · joined Feb 2006 ·

#995035
They are fairly different but they can be retro fitted.

I run an early one in mine they are much stronger than the 73 onwards ones and the rubber mounts are better design too.

My early one (bottom) came from a late 50s split window Kombi.

lou0060 Wolfsburg Wizard

568 posts · joined Dec 2010 ·

#995109
good answers Joel.

seems like your have it in hand...
1971 karmann ghia Cabrio - Cruising 👍
1963 beetle Sunroof - gathering dust 🥲
1968 race beetle - twin turbo Subaru - stress relief 😁
1960 beetle - old school low & slow 😏

lakey Casual Dubber

44 posts · joined Jul 2010 ·

#995123
I will have to check it out the weekend thanks guys.