SOLD - Bolt on Turnkey (Complete) EFI System for Type 1

Lateral · 2013-06-30T05:16:30+00:00

FOR SALE Complete turnkey EFI System for VW motor - $1,950.00. This custom setup was originally installed on the 1916cc motor that was in Stenguns Blue 1967 Beetle and is no longer needed as a new motor running dual carbies has been installed. Everything was working perfectly prior to removing it as I drove the car from Brisbane to Sydney with no problems. Absolutely everything (including a short wiring loom, new looms can be easily purchased) is there to provide a turnkey system...apart from the obvious need to set it up properly and tune it. The ATOM G4 (http://www.linkecu.com/products/engine-management-ecus/g4_atom) is a highly configurable ECU and is configured by downloading the free software from the LinkECU website. All documentation is available free from the website also. I have used their Customer Support as I wanted to find out more about the Atom G4 (they are based in New Zealand) and I have to say that they were really fantastic. The following parts are shown in the attached photo: 1. Custom made Plenum x 1 2. CB Injector inlet manifolds x 2 3. Injectors x 4 (Serviced and flowed at 142cc per minute) 4. Fuel Rails x 2 5. Cold Start circuit x 1 6. KN Style air cleaners x 2 7. 60 mm Single Throttle Body 8. Scat degree pulley fitted with Crank Trigger Wheel x 1 9. Crank trigger sensor x 1 10.Atom G4 ECU with mounting bracket x 1 11.New Injector connectors and boots x 4 12.NEW TPS x 1 13.New Air Temp Sensor x 1 14.Coil pack x 1 15.Piersburg EFI Electric Fuel pump x 1 16.Oil Temp Sensor x 1 (With mounting plate) 17.Fuel regulator x 1 18.Air Cleaner manifold x 1 19.Miscellaneous aluminium tube connection pieces 20.Wiring loom-shortend (not shown as I just found it-21/07/2014) Some interesting things to note: 1. The Atom G4 price new is about $1,200.00 2. The cost of the new TPS was $170.00 3. The cost of the new Air Temp Sensor was $61.00 4. The cost of the injector service etc was $230.00 This comes to more than $1,600.00! As you can see from the above, the $1,950.00 asking price is somewhat of a bargain. Everything is located in Sydney (Willoughby) and I am more than happy to arrange postage if needed. Thanks guys Regards Greg

Boozo Back in the bug

359 posts · joined Sep 2007 · 22 Jul 2014, 6:09 am

#996283

thanks for that, are there any labels left on the loom? and do you have the tuning loom?

'59 or Kombi?....feeling confused

'59 bug
'68 bug
'82 import T3 BUS. aircooled

Lateral Wolfsburg Wizard

480 posts · joined Sep 2011 · 22 Jul 2014, 7:28 am

#996287

Hi mate,

There are no labels but the pin-out diagram for the connector is on page 19 of the documentation is simple and each connector is clearly marked and it would take about 10-15 minutes to label the wiring that you need to use.

Also, I have the USB cable (tuning loom) that is used to connect the Atom G4 ECU to a PC for tuning.

Regards
Greg

Lateral Wolfsburg Wizard

480 posts · joined Sep 2011 · 24 Jul 2014, 7:14 am

#996453

Oh, and you simply download the free PCLINK software for tuning the G4 from the LinkEcu website.

Regards
Greg