| [ Total Views: 965 | Total Replies: 8 | Thread Id: 88932 ] |
|
|
 notshy
Learner Dubber
Posts: 5
Threads: 3
Registered: February 23rd, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 23rd, 2011 at 09:21 PM |
|
|
cylinder not firing
G'day Guys!
New to the formum...but hoping you can help me out? I have a 1500 bug that has started to run rough. We haven't had it very long so we went through
and put new plugs, leads, points and condenser on and still no joy. The mech at work said it sounded as if it was electrical. It does start but
pulling the back left lead off does not affect it when running, pointing to that port being the prob. Plenty of spark, compression about 100. It did
come good for a couple of days at the beginning of all the dramas after I played with the leads but it only lasted a couple of days before it did it
again. I'm starting to run out of ideas, any of yours would be greatly appreciated!! |
|
|
65standard
Officially Full-On Dubber
Posts: 373
Threads: 47
Registered: April 18th, 2009
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue
Mood: Only when I'm in it.
|
| posted on February 23rd, 2011 at 10:13 PM |
|
|
The back left lead is No.4 cylinder. Forward left is No. 3, Rear right is No.2 and forward right is No.1
When you pulled the plug off, what did it look like? Was it oily? If so, you could have shot rings in that cylinder.
Have you checked your valve clearances? They could be too large, opening too late and closing too early. it's possible to have them out in one
cylinder, making it run rough. The clearances should be .006" to .008" depending on who you talk to.
Hope this helps.
[size=4]If it ain't broke, fix it till it is![/size]
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on February 24th, 2011 at 06:37 AM |
|
|
have you checked the tappets
|
|
|
Big Al
Learner Dubber
Posts: 6
Threads: 2
Registered: August 31st, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 24th, 2011 at 08:24 AM |
|
|
I had a similar problem with my VW after fixing an engine fire in that I put the leads on incorrectly. For some reason my engine has been tuned to
fire off no.3 rather than no1 so the leads on the distributer are different from the book? I managed to start the car but it ran very rough.
Also check that your dizzy hasn't moved ( timing).
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on February 24th, 2011 at 08:56 AM |
|
|
That compression is a tad on the low side, not badly but certainly not factory fresh engine.
|
|
|
waveman1500
Custom Title Time!
Also rides a Honda
Posts: 1346
Threads: 13
Registered: December 17th, 2009
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 24th, 2011 at 07:33 PM |
|
|
| Quote: | Originally
posted by Joel
That compression is a tad on the low side, not badly but certainly not factory fresh engine.
|
This is true, but 100psi is still enough to have it run nicely and fire on all four. Have you looked at the distributor cap, rotor button and maybe
even the points cam inside the distributor? Sometimes the points cams can round off with neglect if they're never oiled.
Also look for other faults, is the exhaust blocked? Intake manifold? Do the valves go up and down properly when you turn the engine over by hand?
Oh, and the cylinder numbering that 65standard gives is only correct if you refer to the rearward end of the car as the 'back' cylinder and the
cylinder closest to the driver as the 'front'. Because you work on the engine from the back of the car and reach into the engine bay, I tend to call
#3 and #1 (up against the firewall) the 'back' cylinders, and the ones closest to the engine lid the 'front' (#4 and #2).
|
|
|
ratty 63
A.k.a.: Rossco
Custom Title Time!
Posts: 1083
Threads: 74
Registered: October 1st, 2003
Member Is Offline
Location: Gold Coast, Qld
Theme: UltimaBB Pro Blue ( Default )
Mood: Just cured my shed envy! 
|
| posted on February 25th, 2011 at 09:34 AM |
|
|
Might be a long shot - but have you flooded the engine recently?
I have found that once the spark plugs have been soaked in fuel they don't recover any more. Not sure why - never used to be a problem... perhaps
it's the new fuel or a change in the materials they use in the plugs....
It's also not impossible to have an internal short in a spark plug, even when they are brand new.
Before you get too involved in removing parts for testing it might be worth changing the plugs (particularly the plug in the cylinder that isn't
firing) to check....
R 
|
|
|
notshy
Learner Dubber
Posts: 5
Threads: 3
Registered: February 23rd, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 25th, 2011 at 11:01 AM |
|
|
Thanks for the tips guys, it's given me a few things to look at. My mate has a few parts eg dissy, rotor button that I might try and fault find
with. I did swap all the plugs around to see if it was the 1 dodgey plug, but not the case. The plugs just appear all the same ...just a bit black. |
|
|
notshy
Learner Dubber
Posts: 5
Threads: 3
Registered: February 23rd, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 29th, 2011 at 08:09 AM |
|
|
Well I've been away for a while and not really much the wiser but the bug did come good after a new plug and a good hard drive out on the open road
to clean it out! Thanks again! |
|
|
