| [ Total Views: 923 | Total Replies: 6 | Thread Id: 79634 ] |
|
|
 VWCOOL
23 Windows of Awesome
Posts: 5158
Threads: 235
Registered: June 19th, 2003
Member Is Offline
Location: In the shed... Lake Macquarie NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: happy to help
|
| posted on October 14th, 2009 at 08:48 PM |
|
|
Carb rebuild: Gasket goo, or not?
When installing new float bowl etc gaskets into carbs, should gasket goo such as Permatex be used?
Pay your debts, CxxT
|
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8636
Threads: 559
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
| posted on October 14th, 2009 at 09:01 PM |
|
|
No, spray them with WD 40 makes them live longer
|
|
|
colonel mustard
Son of Jim - Creator of Good
Posts: 2829
Threads: 51
Registered: February 27th, 2009
Member Is Offline
Theme: UltimaBB Pro Black
|
| posted on October 14th, 2009 at 09:12 PM |
|
|
If you use a seal correctly why do you need glue?? Not having a go or anything, it just annoys me when people do it.
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on October 15th, 2009 at 04:13 AM |
|
|
| Quote: | Originally
posted by VWCOOL
When installing new float bowl etc gaskets into carbs, should gasket goo such as Permatex be used?
|
You can use permatex after it has dried..
but as the gaskets are so thin I wouldn't worry..
if they leak later on You could use it....
I always use it on the manifold gasket - both sides.
cheers
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on October 15th, 2009 at 05:28 AM |
|
|
no dont use goo
but make sure there flat you make need to use a very fine file to remove dags or bumps or linish on a piece of glass and 1200 wet n dry with kero
to lubricate
also scrap any old gasket from the surfaces the gaskets are designed to crush and seal
|
|
|
VWCOOL
23 Windows of Awesome
Posts: 5158
Threads: 235
Registered: June 19th, 2003
Member Is Offline
Location: In the shed... Lake Macquarie NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: happy to help
|
| posted on October 15th, 2009 at 06:07 AM |
|
|
| Quote: | Originally
posted by colonel mustard
If you use a seal correctly why do you need glue?? Not having a go or anything, it just annoys me when people do it.
|
tell me about it! I replaced the water pump on my Nissan V6 recently and someone had used rock-hard sealer... It took about one hour, leaning into a
deep engine bay, to scrape the front of the block clean. All the time I was thinking 'i wish this was air cooled...'!
Yep Dave, you are right about the window glass and sanadpaper trick, the throttle body and top cover were both slightly warped so I 'machined' them
flat
Steve - interesting on the WD40. Anyhow, I assmbled the carb 'dry'
Pay your debts, CxxT
|
|
|
alien8
Wolfsburg Wizard
Posts: 521
Threads: 84
Registered: September 5th, 2008
Member Is Offline
Location: Brisbane
Theme: UltimaBB Powder
|
| posted on October 15th, 2009 at 09:48 AM |
|
|
I would usually not use Permatex anywhere near the carb but,,
out of curiosity I touched up the top mating halves of my Bocar with 800 wet or dry on a sanding table before a new carb kit install and tuned it as
normal.
Ran the car around the block a few times and rechecked settings.
Then I took the top half off the carb with it still in the car being careful not to disturb anything else and painted both halves with a thin coating
of Permatex just around the very outside edge of the flats making sure not to get any goo anywhere near any passages.
Then put on the same gasket. Rechecked settings and took the car back out a few times around the block.
Then rechecked the settings again. Nothing was adjusted.
There was a twenty minute difference between the two runs and operating temps were similar.
There was a 150rpm increase at idle on both checks after the Permatex was used.
I am not claiming anything as there is many more variables involved but there is indication there that the Permatex MAY have helped keep
unwanted leaks out of the system .
But its is a Bocar!
|
|
|
