| [ Total Views: 856 | Total Replies: 5 | Thread Id: 91272 ] |
|
|
 type_one
Custom Title Time!
Posts: 1161
Threads: 166
Registered: September 10th, 2002
Member Is Offline
Location: Mount Pleasant. QLD
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 26th, 2011 at 09:38 PM |
|
|
1500 single port engine question
can someone tell me what the left hand side of a 1500 single port engine manifold connects to. not the part that goes on the head but the other part.
it seems to connect to some element thing on the right hand side but left hand side has nothing and appears to have nothing it attaches to. must be
something it is suppose to connect to.
also with this not attached woudld i be getting a major flat spot when i accelerate?
Blank
|
|
|
waveman1500
Custom Title Time!
Also rides a Honda
Posts: 1346
Threads: 13
Registered: December 17th, 2009
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 26th, 2011 at 10:32 PM |
|
|
Have you got a photo? Your description is rather vague. Are you talking exhaust or inlet manifold? I'm assuming that you're talking about the
exhaust crossover for pre-heating the inlet manifold. This takes exhaust from near the head on one side, runs it across the inlet manifold and then
dumps it into the muffler. There should be small two-bolt flanges on both sides which it attaches to, unless you're missing either the factory
muffler or heater boxes.
|
|
|
sander288
Custom Title Time!
"Bolt-on Master"
Posts: 1404
Threads: 183
Registered: August 26th, 2008
Member Is Offline
Location: Norman Park, QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: This is my bug. There are many others like it, but this one is mine.
|
| posted on June 27th, 2011 at 10:09 AM |
|
|
Does the thing your talking about come off the intake pipe just below the carb?
If so this is supposed to be conncect to your warm air intakes in the aircleaner if it were being used. If your not using a stock aricleaner then you
need to plug the hole.
But a better description would help
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on June 27th, 2011 at 12:31 PM |
|
|
Sounds like your manifold preheat discharge has rusted and fallen off.
Is this what's missing? (smaller diameter pipe)
|
|
|
type_one
Custom Title Time!
Posts: 1161
Threads: 166
Registered: September 10th, 2002
Member Is Offline
Location: Mount Pleasant. QLD
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 27th, 2011 at 02:23 PM |
|
|
Thanks all. All think Joel has nailed it. that piece is no where to be seen.
Have not been able to lie under the car where it is. gournds too wet.
So will this be affecting my accelrating when i put my foot down. i have a massive flat spot. when the top part of the carb push down on that little
button like thign that sticks out of it. I know very technical. lol. Maybe pic woudl help.
Just sick of the way it is driving. First sinlgel port i have owned and first flat 1500 type3 motor. Little differnet to what i am used to . Am sure
the principals are the same.
Blank
|
|
|
bushed
Wolfsburg Elder
Posts: 3539
Threads: 66
Registered: December 18th, 2006
Member Is Offline
Location: Lowood Qld
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 27th, 2011 at 03:35 PM |
|
|
check ure timing also by turning
the dizzy
want any vw bits old but like me, Made in Germany!!!
|
|
|
