Skip to content
Aussieveedubbers

Clutch pedal adjustment

0 likes
Share Share on Facebook Share on X Share on Reddit
Log in to reply

blompod Commited Dubber

57 posts · joined Nov 2014 ·

#1006541
I had about 5 inches of play in my clutch pedal, so I adjusted it to what I think is about half and inch of play now. Clutch takes up really high now, that normal? also can you swap out the nut and lock nut for the later wing nut? 7mm thread are they the same?

vw54 Administrator Always Waiting 4 Friday

16,723 posts · joined Aug 2002 ·

#1006543
depends on what clutch arm you have on the gearbox
I read it on FACEBOOK so it must be true


http://forums.aussieveedubbers.com/viewtopic.php?tid=91278&page=1#pid848630


http://forums.aussieveedubbers.com/viewtopic.php?tid=63561&page=1#pid624099


http://forums.aussieveedubbers.com/viewtopic.php?tid=4832&page=1#pid452603


http://forums.aussieveedubbers.com/viewtopic.php?tid=60650&page=1#pid574409

Bizarre Moderator The artist formerly known as blue74l

12,789 posts · joined Aug 2002 ·

#1006545
yes you can swap it over

i would back off so as you have about an 1" of play but otherwise that sounds about right
Futue te ipsum!!!

psimitar Son of Jim - Creator of Good

2,506 posts · joined Jan 2009 ·

#1006554
Nah, just looked it up in me workshop manual and it says 12mm before you reach resistance.
madness is in the eye of the beholder 👍

grumble Son of Jim - Creator of Good

2,672 posts · joined Jun 2008 ·

#1006566
3-5mm free play at the release lever and adjust the pedal rake if necessary for the right stance.

blompod Commited Dubber

57 posts · joined Nov 2014 ·

#1006587
The release lever is the one on the gear box? and how do you adjust the pedal rake? because it is quite forward....

ian.mezz I never said, I could write or spell

3,913 posts · joined Sep 2004 ·

#1006591
you need fee play at gear box. I just adjust mine so they start working about a inch off the floor, that way less chance of riding and wearing out the clutch,
😂🤪😂🤪😂
car forums. where a lot of peoples good intentions end up taking a good old car off the road forever never ever to see the road again. 🥲

psimitar Son of Jim - Creator of Good

2,506 posts · joined Jan 2009 ·

#1006678
blompod wrote:The release lever is the one on the gear box? and how do you adjust the pedal rake? because it is quite forward....
Pedal rake adjusted by the stop plate on the floor behind the clutch and brake pedal pivot. This should be adjusted first for how you like the pedals set.

Then you adjust both the brake pedal actuation rod and clutch pedal freeplay.

yes the release arm is on the passenger side of the gearbox. doing grumbles method means you don't have to keep get under the vehicle to make additional adjustments but you have to push against the arms spring force until you feel extra resistance of the clutch pressure plate so can be harder to do.
madness is in the eye of the beholder 👍

grumble Son of Jim - Creator of Good

2,672 posts · joined Jun 2008 ·

#1006690
psimitar wrote:
blompod wrote:The release lever is the one on the gear box? and how do you adjust the pedal rake? because it is quite forward....
Pedal rake adjusted by the stop plate on the floor behind the clutch and brake pedal pivot. This should be adjusted first for how you like the pedals set.

Then you adjust both the brake pedal actuation rod and clutch pedal freeplay.

yes the release arm is on the passenger side of the gearbox. doing grumbles method means you don't have to keep get under the vehicle to make additional adjustments but you have to push against the arms spring force until you feel extra resistance of the clutch pressure plate so can be harder to do.
The adjustment is easy to do,1st check the pedal rake as if he had 5" of free travel the pedal rake should be fairly well back towards the seat, adjust the brake pushrod if required to achieve 3mm free play then slide under the car and pull the release lever until it hits the thrust pad adjust the cable for 3-5mm clearance and that is it.
When checking the free play at the pedal it id easy to get it wrong as you have extra leverage whereas if it is done at the release lever it has to be correct.