alien8 Wolfsburg Wizard
521 posts · joined Sep 2008 ·
Where are you?
WTB: extractors
jacky_moo Seriously Crusin Dubber
115 posts · joined Feb 2010 ·
In Melbourne
schnell!! schnell!! schnell!! schnell!!
jacky_moo Seriously Crusin Dubber
115 posts · joined Feb 2010 ·
[edit] No longer need the carby but still after the manifold and extractors
schnell!! schnell!! schnell!! schnell!!
jacky_moo Seriously Crusin Dubber
115 posts · joined Feb 2010 ·
stoßen!!
bump*
bump*
schnell!! schnell!! schnell!! schnell!!
Craig Torrens 6 times Australian, 7 times State Hillclimb Class Champion
8,040 posts · joined Jan 2003 ·
I have some new extractors....will send you a pm.
esevwbits Custom Title Time!
1,027 posts · joined Jun 2003 ·
I have a set of these for sale
$130.00
postage to melb $25
$130.00
postage to melb $25
jacky_moo Seriously Crusin Dubber
115 posts · joined Feb 2010 ·
hey esevwbits thanks for that but im after some stock style ones ... sorry really should have clarified that
as i currently have and exhaust set up very much the same as that pictured above..
Im after a standard style performance system
as i currently have and exhaust set up very much the same as that pictured above..
Im after a standard style performance system
schnell!! schnell!! schnell!! schnell!!
jacky_moo Seriously Crusin Dubber
115 posts · joined Feb 2010 ·
Bump Im still after a set of stock style extractors
Like those pictured above!
Like those pictured above!
schnell!! schnell!! schnell!! schnell!!
funbug Seriously Crusin Dubber
135 posts · joined May 2006 ·
Try George at Classic Veedub. I got stainless ones off him.jacky_moo wrote:Bump Im still after a set of stock style extractors
Like those pictured above!
alien8 Wolfsburg Wizard
521 posts · joined Sep 2008 ·
Hey mate ,whats with the two short elbow pipes under the heat riser connections. Never seen that before on a header.esevwbits wrote:I have a set of these for sale
$130.00
postage to melb $25
funbug Seriously Crusin Dubber
135 posts · joined May 2006 ·
Connects to the heater boxes and to the foil or plastic pipes from the fan shroudalien8 wrote:Hey mate ,whats with the two short elbow pipes under the heat riser connections. Never seen that before on a header.esevwbits wrote:I have a set of these for sale
$130.00
postage to melb $25
Bizarre Moderator The artist formerly known as blue74l
12,787 posts · joined Aug 2002 ·
Get the stainless one
Good for the money
Good for the money
Futue te ipsum!!!
alien8 Wolfsburg Wizard
521 posts · joined Sep 2008 ·
I am using the Empi version of this system atm and I had to flatten one of the lower pipes a little to clear the full flow pump cover. Does the stainless version from George suffer this problem too? I like the system itself but, god, the Empi system is just woeful quallity.Bizarre wrote:Get the stainless one
Good for the money
Bizarre Moderator The artist formerly known as blue74l
12,787 posts · joined Aug 2002 ·
mmmmmmmmmmm..........doubt it would foul
There is about 20??mm between the pump cover and top pipes from 2 and 4
That said i am currently going to a custom built set up
I flanged my connections because it didnt want to seal properly. Dont know if it was the fault of the extractor
I hate all extractors equally for this reason
And ALL exhausts suffer from poor design regarding the heat riser take offs
These ones werent even drilled. Any heat to the manifold is purely conduction
That said - it works ok at stopping incing.
As an extractor - it is not much better than a stock set up
But i like the fact the pea shooters are fixed
As i said - for the money they are ok
Pity you cant buy a stock exhaust in stainless
There is about 20??mm between the pump cover and top pipes from 2 and 4
That said i am currently going to a custom built set up
I flanged my connections because it didnt want to seal properly. Dont know if it was the fault of the extractor
I hate all extractors equally for this reason
And ALL exhausts suffer from poor design regarding the heat riser take offs
These ones werent even drilled. Any heat to the manifold is purely conduction
That said - it works ok at stopping incing.
As an extractor - it is not much better than a stock set up
But i like the fact the pea shooters are fixed
As i said - for the money they are ok
Pity you cant buy a stock exhaust in stainless
Futue te ipsum!!!
alien8 Wolfsburg Wizard
521 posts · joined Sep 2008 ·
I like that this system comes out of the stock cut outs and has good ground clearence.
20mm from stock pump cover to pipe I am pretty sure that would foul my style of full flow cover.(old Burg style) The base on the cover is prob 8-10mm thick plus the outlet barb sticks out another 25-30mm.
I am looking at a stainless hideaway style this time around and like you, get some flanges welded on the J pipes. I bloody hate those doughnut gaskets. Does the stainless system have baffels fitted in the tail pipes?
20mm from stock pump cover to pipe I am pretty sure that would foul my style of full flow cover.(old Burg style) The base on the cover is prob 8-10mm thick plus the outlet barb sticks out another 25-30mm.
I am looking at a stainless hideaway style this time around and like you, get some flanges welded on the J pipes. I bloody hate those doughnut gaskets. Does the stainless system have baffels fitted in the tail pipes?
Bizarre Moderator The artist formerly known as blue74l
12,787 posts · joined Aug 2002 ·
yeah - same as the other onealien8 wrote:. Does the stainless system have baffels fitted in the tail pipes?
Futue te ipsum!!!
jacky_moo Seriously Crusin Dubber
115 posts · joined Feb 2010 ·
No longer need a set just going for an OEM muffler .. now to find some trumpets ... FWEEP FWEEP here we come!
schnell!! schnell!! schnell!! schnell!!