typethreeking Wolfsburg Wizard
621 posts · joined May 2008 ·
more boost this year bec, dont forget the score is two- nil to me...hahaha
BEING ASPIRATED FEELS GREAT BUT BEING BLOWN TAKES THING TO A WHOLE NEW LEVEL....
Bec's type 3 rotary
13b type 3 Casual Dubber
42 posts · joined May 2009 ·
cheeky, very cheeky
hey it was my first time drag racing
what was the time difference when we raced, i cant remember.
More boost hey maybe i should mmmmm
😀
hey it was my first time drag racing
what was the time difference when we raced, i cant remember.
More boost hey maybe i should mmmmm
😀
hellbugged 48's and straight cuts
5,080 posts · joined Apr 2003 ·
shakedown at Valla lap dash...........then on to Warwick drags i say 😍
13b type 3 Casual Dubber
42 posts · joined May 2009 ·
valla cant wait its my first year with my car, crusing down thursday from the gold coast, will just be watching the lap dash.
Aaron is thinking about taking the kombi 20b around again this year, but for the cams license he needs to get a signature from a car club associated with racing. so he is looking into it.
Aaron is thinking about taking the kombi 20b around again this year, but for the cams license he needs to get a signature from a car club associated with racing. so he is looking into it.
hellbugged 48's and straight cuts
5,080 posts · joined Apr 2003 ·
clubVW Sydney is CAMS associated now...........get a nice magazine/news book every month along with it too
do it all through their site without leaving your desk!
look for "join clubVW" tab on the left pane
http://www.clubvw.org.au/
glad you are looking forward to the Spectacular, not far away now!
do it all through their site without leaving your desk!
look for "join clubVW" tab on the left pane
http://www.clubvw.org.au/
glad you are looking forward to the Spectacular, not far away now!
13b type 3 Casual Dubber
42 posts · joined May 2009 ·
Thanks🙂
vassy66T1 Wow ... are U reading this?
2,120 posts · joined Jun 2003 ·
Go the manual Bec ... that would be excitement 😎
typethreeking Wolfsburg Wizard
621 posts · joined May 2008 ·
i think i ran a 8.3 and you a 8.5 for memory, should be good to have another run this year all going to plan
BEING ASPIRATED FEELS GREAT BUT BEING BLOWN TAKES THING TO A WHOLE NEW LEVEL....
colonel mustard Son of Jim - Creator of Good
2,829 posts · joined Feb 2009 ·
From Yatala pie's. 🙂
This what you're talk about Troy??
This what you're talk about Troy??
13b type 3 Casual Dubber
42 posts · joined May 2009 ·
Thanks colonel 😵💫
LIFE IN THE LOW LANE All people have the right to stupidity but some abuse the pr
2,534 posts · joined Mar 2007 ·
Hopefully Troy won't be doing his "puffing billy" impersonations this year... LOL
ACCEPT THAT SOME DAYS YOU ARE THE PIDGEON AND SOME DAYS YOU ARE THE STATUE
Alder Outlaws VW Racing - check it out on fb!!
Alder Outlaws VW Racing - check it out on fb!!
nsuwift Seriously Crusin Dubber
127 posts · joined Mar 2010 ·
hi was wondering how to tell if a rotary engine is stuffed or not without pulling it apart. My mate has a series 4(I think) rx7 I can buy for $200. As far as I know the engine does not start. It would be to go in to a notchback. How much did your conversion cost comparitavely to a subaru transplant
13b type 3 Casual Dubber
42 posts · joined May 2009 ·
hi,
If you can turn it over with a starter motor, use a compression tester. when doing this keep the throttle wide open and take out only 1 leading spark plug,
insert gauge and KEEP FINGER ON THE RELEASE BUTTON. As the motor turns over you will see the needle bounce up, once every revolution. if it moves
3 times in a row and around 70-90 psi the engine is fine.
This will have to be done to the rear rotor housing as well
If the needle is low on one of 3 cycles a side seal is stuck in the rotor or is broken(if this is the case pour 50 ml of oil in the spark plug hole and try starting)
this will help seal any stuck seals and hopfully free them up.
if the needle is low in 2 of the cycles out of the 3 this might mean that apex seals or corner seals are broken(time for rebuild)
if there is no starter motor you can turn it over by hand and use your thumb to feel compression once every revolution again.
with cost would be the same if you have the ecu
and loom
good luck with the engine and its dirt cheap
If you can turn it over with a starter motor, use a compression tester. when doing this keep the throttle wide open and take out only 1 leading spark plug,
insert gauge and KEEP FINGER ON THE RELEASE BUTTON. As the motor turns over you will see the needle bounce up, once every revolution. if it moves
3 times in a row and around 70-90 psi the engine is fine.
This will have to be done to the rear rotor housing as well
If the needle is low on one of 3 cycles a side seal is stuck in the rotor or is broken(if this is the case pour 50 ml of oil in the spark plug hole and try starting)
this will help seal any stuck seals and hopfully free them up.
if the needle is low in 2 of the cycles out of the 3 this might mean that apex seals or corner seals are broken(time for rebuild)
if there is no starter motor you can turn it over by hand and use your thumb to feel compression once every revolution again.
with cost would be the same if you have the ecu
and loom
good luck with the engine and its dirt cheap
13b type 3 Casual Dubber
42 posts · joined May 2009 ·
Mmmmm, where do i start. Well our garage has a 20b engine apart, a porsche gearbox apart, a 010 auto box apart, TMI carpets and head lining all to go back
into our cars before valla. Aarons been working very hard to make this happen and will start working on the interior this weekend.
I'll post pictures of the mods Aarons done to the gearbox soon.😁😁
into our cars before valla. Aarons been working very hard to make this happen and will start working on the interior this weekend.
I'll post pictures of the mods Aarons done to the gearbox soon.😁😁
Dasdubber DAS Resto Haus
5,746 posts · joined Aug 2002 ·
Hey Bec, good to hear you'll have a complete interior soon! I'm sure Aaron is a man on a mission as usual and I'm sure you're not far behind doing the hard yards as well. Look forward to catching up at Valla!
Al
PS hopefully the shirts/cd arrived okay.
Al
PS hopefully the shirts/cd arrived okay.
nsuwift Seriously Crusin Dubber
127 posts · joined Mar 2010 ·
thanks for the info will give it a try. Will you be at valla would love to see your setup.
13b type 3 Casual Dubber
42 posts · joined May 2009 ·
hi, alan
i tried calling you the other day when we recieved the package to say thanks for the shirts and the dvd, i left a message.
maybe i have the wrong number, all good thanks so much for that.
yes will catch up at valla, we are leaving the thursday morning early. 😵💫
i tried calling you the other day when we recieved the package to say thanks for the shirts and the dvd, i left a message.
maybe i have the wrong number, all good thanks so much for that.
yes will catch up at valla, we are leaving the thursday morning early. 😵💫
skelaaleks Seriously Crusin Dubber
116 posts · joined Apr 2008 ·
👍 some good timestypethreeking wrote:i think i ran a 8.3 and you a 8.5 for memory, should be good to have another run this year all going to plan
13bt aztec