Stalling in the morning

Blue65 Officially Full-On Dubber

298 posts · joined Sep 2002 · 31 Aug 2012, 1:07 am

#920121

Hi. My VW thens to stall as I slow down to take a corner or brake - this only happens in the first 5 - 10 minutes of driving, afterwards its OK.

Its always been like this - got several VW mechanics to check it out and they say not much can be done. One of them fitted an electrical warming kit to the carbie but can't remember whether that worked well.

Any solutions anyone

______________________
Owner of a 1964 VW Beetle, 1641cc engine, etc..

Bob down Wolfsburg Wizard

455 posts · joined Jan 2012 · 31 Aug 2012, 5:38 am

#920123

mine does the same until it warms up properly, i thought this was normal with an original carb setups, but i could be wrong.

tar76 Custom Title Time!

1,622 posts · joined Dec 2009 · 31 Aug 2012, 7:29 am

#920134

Do you let it warm up before driving or do you just jump in and go?

"Obey your Dreams"!

62 Std beetle.
65 11 wnd Split "The Cross".
6? coming very soon!!!!

annosL Officially Full-On Dubber

378 posts · joined Dec 2008 · 31 Aug 2012, 11:43 am

#920170

I had this with my '60 beetle, then fitted the pipe to original air cleaner from the hot air outlet at the back of the motor(as original) so the air cleaner gets warm air a lot quicker as the weighted flap closes at low revs, this solved the stalling and flat spot as well

sander288 "Bolt-on Master"

1,404 posts · joined Aug 2008 · 31 Aug 2012, 11:46 am

#920171

I'd be looking at the auto-choke on the carb (if its standard) and also check that the pre-heat pipes are connected and working.

Something else that will help is having the proper thermostat and flaps; you get a quick warm-up

With all the above said I lived through several new england winters with my bug and never had any of the above and if you do give it 10min then she'll be sweet

BMW R65 LS
1967 1300 Deluxe
Swing-axles FTW ❗

68AutoBug Beetle Restorer - Experience over 138\% - YIKES --

11,654 posts · joined Aug 2002 · 31 Aug 2012, 12:59 pm

#920177

tar76 wrote:Do you let it warm up before driving or do you just jump in and go?

The idea of the automatic choke which was a big selling point of beetles in the 60s

You get in push the accelerator down once
[to bring the automatic choke into action]
then start the engine and Drive off...

Don't warm up the engine by idling..

the automatic chokes do need some adjusting between winter and summer etc.

You loosen the automatic choke by the 3 screws holding it in place.. just loosen the 3 screws and turn the choke unit
anticlockwise for More choke...
clockwise for less choke..

If You take the air cleaner off You can see the choke flap close over [more choke - more strangler in the UK] lol

just adjust it.. engine cold... and see how the engine starts..

the wire to the automatic choke heats the choke up and once it gets to the correct temperature the choke is completely OFF...

also check the stepped piece that adjusts how much throttle
is applied when the choke is cold...
adjustment screw also... Best not to have your engine revving too fast when You first start it...

LEE

- Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY---

hellbugged 48's and straight cuts

5,080 posts · joined Apr 2003 · 31 Aug 2012, 1:34 pm

#920189

Manifold heat risers blocked.

68AutoBug Beetle Restorer - Experience over 138\% - YIKES --

11,654 posts · joined Aug 2002 · 31 Aug 2012, 4:10 pm

#920203

hellbugged wrote:Manifold heat risers blocked.

Yes, blocked heat risers can also affect Your car when cold in cold weather..

also. if the auto choke heats up and turns off as its supposed to
then No Heat Risers [heated inlet manifold] this can affect Your car... if its Really Cold [under 5C] then Your engine can stop and stay stopped until the ice melts.. etc

LEE

- Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY---

bajachris88 The international telephone dialing code for Antarctica is 6

6,661 posts · joined Apr 2005 · 31 Aug 2012, 5:55 pm

#920227

I tend to get this too! when cold, but also moreso when driving down hill while cold :S!

I try to down shift and crawling to an intersection to prevent, and if you got a stop, blip the throttle. Although for me it doesn't always work haha.

Full ignition and carby tune up wouldn't go astray 👍 But age and wear creating vacuum pressure losses (eg: carb shafts wearing the bores they sit in etc) in theory should have some minor detriment to the auto choke, which tries to induce greater vacuum pressure and thus 'enrich' the air fuel mixture to keep the dakka happy in the morning. But then loose that vacuum pressure through sucking in air through those worn bores etc.

(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears. 👍
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta!

68AutoBug Beetle Restorer - Experience over 138\% - YIKES --

11,654 posts · joined Aug 2002 · 31 Aug 2012, 8:34 pm

#920280

You need to keep those linkages and shafts etc well oiled

they were done at every oil change back in the 60s & maybe 70s... as per the service handbook etc

Lee

- Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY---

rcarnold1957 Learner Dubber

13 posts · joined Mar 2009 · 1 Sep 2012, 12:16 pm

#920356

Sorry to butt in, I've had problems with blocked heat risers too. I ended up having to cut, clean and reweld the pipe. Has anyone got an alternative method of cleaning the carbon out?

Blue65 Officially Full-On Dubber

298 posts · joined Sep 2002 · 3 Sep 2012, 4:14 pm

#920706

68AutoBug wrote:You need to keep those linkages and shafts etc well oiled

they were done at every oil change back in the 60s & maybe 70s... as per the service handbook etc

Lee

What linkages and shafts are you referring to please?

______________________
Owner of a 1964 VW Beetle, 1641cc engine, etc..

68AutoBug Beetle Restorer - Experience over 138\% - YIKES --

11,654 posts · joined Aug 2002 · 3 Sep 2012, 5:17 pm

#920712

rcarnold1957 wrote:Sorry to butt in, I've had problems with blocked heat risers too. I ended up having to cut, clean and reweld the pipe. Has anyone got an alternative method of cleaning the carbon out?

I replaced Mine as they had been cleaned out and welded up twice.. then they rusted thru all along the rear side...
I believe once they start to rust... they keep on rusting..
I sprayed My replacement with heat proof paint inside and out the other side.. whether that will help??
Maybe a grease nipple would help and a bit of grease now & then... I read that years ago for an exhaust system..
to help stop the muffler rusting out..

I suppose a stainless steel sleeve or pipe inside it.. cut & shut

cheers

LEE

- Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY---

rcarnold1957 Learner Dubber

13 posts · joined Mar 2009 · 3 Sep 2012, 7:58 pm

#920747

Thanks Lee, I like the idea of a grease nipple, should stop the carbon bonding to the surface. Thanks for your help.

68AutoBug Beetle Restorer - Experience over 138\% - YIKES --

11,654 posts · joined Aug 2002 · 7 Sep 2012, 4:09 pm

#921187

Blue65 wrote:
68AutoBug wrote:You need to keep those linkages and shafts etc well oiled

they were done at every oil change back in the 60s & maybe 70s... as per the service handbook etc

Lee
What linkages and shafts are you referring to please?

Hi
You need to oil [one drop will do] on every moving part on the carburetor..
mainly the shafts that stick out on both sides.
they need lubricatiing with oil to help stop them wearing out
I oil mine every month or so, and wipe any excess off
as its hard to get just one drop with an oil can.. lol

the spring tension is a major wearing cause on the shaft

I hope that helps..

[old beetles had a grease nipple on the clutch/brake pedals too] so a drop of oil there is good but harder to get to

LEE

- Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY---